IS25LP256D-RGLA3 datasheet(2/174 Pages) ISSI

2 / 174 page

IS25LP256D

IS25WP256D

Integrated Silicon Solution, Inc.- www.issi.com

Rev A6

04/15/2019

FEATURES

 Industry Standard Serial Interface

- IS25LP256D: 256Mbit/32Mbyte

- IS25WP256D: 256Mbit/32Mbyte

- 3 or 4 Byte Addressing Mode

- Supports Standard SPI, Fast, Dual, Dual

I/O, Quad, Quad I/O, SPI DTR, Dual I/O

DTR, Quad I/O DTR, and QPI

- Software & Hardware Reset

- Supports Serial Flash Discoverable

Parameters (SFDP)

 High Performance Serial Flash (SPI)

- 80MHz Normal Read

- Up to166Mhz Fast Read:

-166MHz at Vcc=2.7V to 3.6V (1)

-133MHz at Vcc=2.3V to 3.6V

-133MHz at Vcc=1.65V to 1.95V (2)

- Up to 80MHz DTR (Dual Transfer Rate)

- Equivalent Throughput of 664 Mb/s

- Selectable Dummy Cycles

- Configurable Drive Strength

- Supports SPI Modes 0 and 3

- More than 100,000 Erase/Program Cycles

- More than 20-year Data Retention

 Flexible & Efficient Memory Architecture

- Chip Erase with Uniform Sector/Block

Erase (4/32/64 Kbyte)

- Program 1 to 256 Byte per Page

- Program/Erase Suspend & Resume

 Efficient Read and Program modes

- Low Instruction Overhead Operations

- Continuous Read 8/16/32/64 Byte

Burst Wrap

- Selectable Burst Length

- QPI for Reduced Instruction Overhead

- AutoBoot Operation

 Low Power with Wide Temp. Ranges

- Single Voltage Supply

IS25LP: 2.30V to 3.60V

IS25WP: 1.65V to 1.95V

- 7.5 mA Active Read Current

- 10 µA Standby Current

- 1 µA Deep Power Down

- Temp Grades:

Extended: -40°C to +105°C

Auto Grade (A3): -40°C to +125°C

 Advanced Security Protection

- Software and Hardware Write Protection

- Advanced Sector/Block Protection

- Top/Bottom Block Protection

- Power Supply Lock Protection

- 4x256 Byte Dedicated Security Area

with OTP User-lockable Bits

- 128 bit Unique ID for Each Device

(Call Factory)

 Industry Standard Pin-out & Packages

- M =16-pin SOIC 300mil

- L = 8-contact WSON 8x6mm

- J = 8-contact WSON 8x6mm (3)

- G = 24-ball TFBGA (4x6 ball array)

- H = 24-ball TFBGA (5x5 ball array)

- KGD (Call Factory)

Note:

166MHz at Mode 0 , and 133MHz at Mode 3

104MHz with 3-byte address (24-bit address) fast read

operation

Exposed Pad Size = 3.4mmx4.3mm instead of

4.7mmx4.7mm

256Mb

SERIAL FLASH MEMORY WITH 166MHZ MULTI I/O SPI &

QUAD I/O QPI DTR INTERFACE

IS25LP256D-RGLA3 Datasheet(PDF) 2 Page - Integrated Silicon Solution, Inc

IS25LP256D-RGLA3 Datasheet(HTML) 2 Page - Integrated Silicon Solution, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL