CS49310 datasheet(64/90 Pages) CIRRUS

64 / 90 page

CS49300 Family DSP

DS339F7

application to initialize, the host can send

configuration messages for both hardware and

software configuration.

This method of resetting the DSP is usually

referred to as a “soft reset” even though it involves

toggling the reset pin.

Table 12 lists some possible external memory

configurations for each DSP, in conjunction with

IBA codes stored in the host microcontroller. The

table provides a list of the ROM content, the size of

the combined memory images, the recommended

page size, and the number of discrete pages

required. The examples also include several

figures

which

present

the

different

ROM

configurations as composite memory images.

The CS49292, CS493102, and CS493112 all have

special memory requirements since they must

have access to external SRAM (70nS or faster)

during the decoding of AAC Multichannel (5.1

Channel) audio. More specifically this SRAM

requirement is ONLY required for AAC application

code which is capable of outputting 5.1 discrete

channels, but is not required of application code

that offers a 2 channel downmixed output.

Also, for the CS49330, there are certain releases

THX Surround EX (5.1 Channel and 7.1 Channel

versions), and THX Ultra2 Cinema (7.1 Channel

version only) application codes that offer additional

all-channel delay, and for this a 1Mbit or 2Mbit,

70nS SRAM is also required. The THX Surround

EX application codes (5.1 Channel or 7.1 Channel)

nor the THX Ultra2 Cinema code do not require

external

SRAM.

Please

refer

the

CS4932X/CS49330 Part Matrix vs. Code Matrix for

more detail about each particular application code.

The speed of external ROM or Flash Memory need

only be 330nS (or faster) which stores the

application codes, while the speed of the SRAM

must be 70nS or faster.

8.7. External Memory Examples

8.7.1. Non-Paged Autoboot Memory

The most rudimentary memory design discussed

above is the non-paged memory. In a non-paged

design, the DSP can only access one item in

memory which could be either a single full

download code load. The memory image given in

Figure 39. Performing a Reset

WRITE_*

WRITE_* (SOFTRESET,

MSG_SIZE)

RESET(LOW) (NOTE 1)

RESET(HIGH) (NOTE 2)

WAIT

500

µs

WAIT 5 ms (NOTE 3)

(CONFIGURATION_MESSAGES,

CONFIG_MSG_SIZE)

(NOTE 4)

Notes: 1. RESET must be held LOW for trstl.

2. It should be noted that mode pins are used to configure

the CS493XX communication mode. These mode pins

are latched internally on the rising edge of reset and

can be set dynamically by a microprocessor or can be

statically pulled HIGH or LOW. If these pins are driven

dynamically, setup and hold times must be satisfied as

stated in the CS493XX Datasheet. More information

about the function of the mode pins can be found in the

CS493XX Datasheet and in Section 6, “Control” on

page 36.

3. 5 ms is typical but this time is application code specific

and may be as high as 10 ms. Wait times should be

verified by the designer.

4. Configuration messages determine both hardware and

software configuration. Hardware configurations are

described in Section 11 of this manual. Software

application configuration messages are described in

the Application Code User’s Guide for the code being

used.

CS49310 Datasheet(PDF) 64 Page - Cirrus Logic

CS49310 Datasheet(HTML) 64 Page - Cirrus Logic

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90

Datasheet Download

Link URL