MPC8314EVRADDA datasheet(14/101 Pages) FREESCALE

14 / 101 page

MPC8314E PowerQUICC II Pro Processor Hardware Specifications, Rev. 2

Freescale Semiconductor

Clock Input Timing

5.1

DC Electrical Characteristics

This table provides the clock input (SYS_CLK_IN/PCI_SYNC_IN) DC timing specifications for the

MPC8314E.

5.2

AC Electrical Characteristics

The primary clock source for the MPC8314E can be one of two inputs, SYS_CLK_IN or PCI_CLK,

depending on whether the device is configured in PCI host or PCI agent mode. This table provides the

clock input (SYS_CLK_IN/PCI_CLK) AC timing specifications for the MPC8314E.

Table 6. SYS_CLK_IN DC Electrical Characteristics

Parameter

Condition

Symbol

Min

Max

Unit

Input high voltage

—

VIH

2.4

NVDD + 0.3

Input low voltage

—

VIL

-0.3

0.4

SYS_CLK_IN input current

0 V

V

IN NVDD

IIN

—±10

A

SYS_XTAL_IN input current

0 V

V

IN NVDD

IIN

—±40

A

PCI_SYNC_IN input current

0 V

V

IN NVDD

IIN

—±10

A

RTC_CLK input current

0 V

V

IN NVDD

IIN

—±10

A

USB_CLK_IN input current

0 V

 V

IN  NVDD

IIN

—±10

A

USB_XTAL_IN input current

0 V

V

IN NVDD

IIN

—±40

A

Table 7. SYS_CLK_IN AC Timing Specifications

Parameter/Condition

Symbol

Min

Typical

Max

Unit

Note

SYS_CLK_IN/PCI_CLK frequency

fSYS_CLK_IN

—

66.67

MHz

1, 6, 7

SYS_CLK_IN/PCI_CLK cycle time

tSYS_CLK_IN

—

41.6

SYS_CLK_IN rise and fall time

tKH, tKL

0.6

—

2, 6

PCI_CLK rise and fall time

tPCH, tPCL

0.6

0.8

1.2

SYS_CLK_IN/PCI_CLK duty cycle

tKHK/tSYS_CLK_IN

—

3, 6

SYS_CLK_IN/PCI_CLK jitter

—

±150

4, 5, 6

Note:

1. Caution: The system, core, and security block must not exceed their respective maximum or minimum operating

frequencies.

2. Rise and fall times for SYS_CLK_IN/PCI_CLK are specified at 20% to 80% of signal swing.

3. Timing is guaranteed by design and characterization.

4. This represents the total input jitter—short term and long term—and is guaranteed by design.

5. The SYS_CLK_IN/PCI_CLK driver’s closed loop jitter bandwidth should be <500 kHz at –20 dB. The bandwidth must be set

low to allow cascade-connected PLL-based devices to track SYS_CLK_IN drivers with the specified jitter.

6. The parameter names PCI_CLK and PCI_SYNC_IN are used interchangeably in this document.

7. Spread spectrum is allowed up to 1% down-spread at 33kHz.(max. rate).

MPC8314EVRADDA Datasheet(PDF) 14 Page - Freescale Semiconductor, Inc

MPC8314EVRADDA Datasheet(HTML) 14 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL