USB3370 datasheet(48/75 Pages) MICROCHIP

48 / 75 page

USB3370

DS00001915B-page 48

 2012 - 2015 Microchip Technology Inc.

In serial mode, interrupts are possible from unmasked sources. The state of each interrupt source is sampled prior to

the assertion of DIR and this is compared against the asynchronous level from interrupt source.

Exiting the serial modes is the same as exiting Low Power Mode. The Link must assert STP to signal the PHY to exit

serial mode. When the PHY can accept a command, DIR is de-asserted and the PHY will wait until the Link de-asserts

STP

to resume synchronous ULPI operation. The RESETB pin can also be pulsed low to reset the USB3370 and return

it to Synchronous Mode.

6.6.1

3-PIN FS/LS SERIAL MODE

Three pin serial mode utilizes the data bus pins for the serial functions shown in Table 6-8.

6.6.2

6-PIN FS/LS SERIAL MODE

Six pin serial mode utilizes the data bus pins for the serial functions shown in Table 6-9.

6.7

Carkit Mode

The USB3370 includes Carkit Mode to support a USB UART Mode.

By entering Carkit Mode, the USB3370 current drain is minimized. The internal PLL is disabled and the 60MHz ULPI

CLKOUT

will be stopped to conserve power by default. The Link may configure the 60MHz clock to continue by setting

the ClockSuspendM bit of the Interface Control register before entering Carkit Mode. If set, the 60 MHz clock will con-

tinue during the Carkit Mode of operation.

In Carkit Mode, interrupts are possible if they have been enabled in the Carkit Interrupt Enable register. The state of

each interrupt source is sampled prior to the assertion of DIR and this is compared against the asynchronous level from

interrupt source. In Carkit Mode, the Linestate signals are not available per the ULPI specification.

The ULPI interface is redefined to the following when Carkit Mode is entered.

TABLE 6-8:

PIN DEFINITIONS IN 3 PIN SERIAL MODE

Signal

Connected To

Direction

Description

tx_enable

DATA[0]

Active High transmit enable.

data

DATA[1]

I/O

TX differential data on DP/DM when tx_enable is high.

RX differential data from DP/DM when tx_enable is low.

SE0

DATA[2]

I/O

TX SE0 on DP/DM when tx_enable is high.

RX SE0_b from DP/DM when tx_enable is low.

interrupt

DATA[3]

OUT

Asserted when any unmasked interrupt occurs. Active high.

Reserved

DATA[7:4]

OUT

Driven Low.

TABLE 6-9:

PIN DEFINITIONS IN 6 PIN SERIAL MODE

Signal

Connected To

Direction

Description

tx_enable

DATA[0]

Active High transmit enable.

tx_data

DATA[1]

Tx differential data on DP/DM when tx_enable is high.

tx_se0

DATA[2]

Tx SE0 on DP/DM when tx_enable is high.

interrupt

DATA[3]

OUT

Asserted when any unmasked interrupt occurs. Active high.

rx_dp

DATA[4]

OUT

Single ended receive data on DP.

rx_dm

DATA[5]

OUT

Single ended receive data on DM.

rx_rcv

DATA[6]

OUT

Differential receive data from DP and DM.

Reserved

DATA[7]

OUT

Driven Low.

USB3370 Datasheet(PDF) 48 Page - Microchip Technology

USB3370 Datasheet(HTML) 48 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

Datasheet Download

Link URL