R8CSLASH13 datasheet(73/224 Pages) RENESAS

73 / 224 page

Rev.1.20

Jan 27, 2006

page 62 of 205

REJ09B0111-0120

R8C/13 Group

______

10.2.3 INT1 Interrupt and INT2 Interrupt

______

INT1 interrupts are triggered by INT1 inputs. The edge polarity can be selected with the R0EDG bit in

______

the TXMR register. The INT1 pin is shared with the CNTR0 pin.

______

INT2 interrupts are triggered by INT2 inputs. The edge polarity can be selected with the R1EDG bit in

______

the TYZMR register. The INT2 pin shared with the CNTR1 pin.

______

_____

Figure 10.13 shows the TXMR and TYZMR registers when using INT1 and INT2 interrupts.

______

Figure 10.13 TXMR Register and TYZMR Register when INT1 and INT2 Interrupt Used

Timer X mode register

SymbolAddressAfter reset

TXMR008B16

0016

Bit name

Function

Bit symbol

b7 b6 b5 b4 b3 b2 b1 b0

0 0 : Timer mode or pulse period

measurement mode(3)

b1 b0

TXMOD2

TXS

TXMOD1

R0EDG

TXMOD0

TXOCNT

Operation mode

select bit 0, 1

Timer X count

start flag

0 : Stops counting

1 : Starts counting

Operation mode

select bit 2

Set to "0" in timer mode

0 : Rising edge

1 : Falling edge

TXEDG

TXUND

INT1/CNTR0 polarity

switching bit(1, 2)

Set to "0" in timer mode

0 : Other than pulse period measurement

mode(3)

NOTES:

1. The IR bit in the INT1IC may be set to “1” (interrupt requested) when the R0EDG bit is rewritten. Refer to the

paragraph 19.2.5 “Changing Interrupt Factor” in the Usage Notes Reference Book.

2. This bit is used to select the polarity of INT1 interrupt in timer mode.

3. When using INT1 interrupts, should select timer mode.

Timer Y, Z mode register

SymbolAddressAfter reset

TYZMR008016

0016

Bit name

Function

Bit symbol

b7 b6 b5 b4 b3 b2 b1 b0

TZMOD1

TYS

TYWC

TYMOD0

TZMOD0

Timer Y operation

mode bit

Timer Y write

control bit

Functions varies depending on

the operation mode

0 : Timer mode(1)

TZWC

TZS

0 : Stops counting

1 : Starts counting

Timer Z-related bit

Timer Y count

start flag

R1EDG

0 : Rising edge

1 : Falling edge

INT2/CNTR1 polarity

switching bit(2)

NOTES:

1. When using INT2 interrupts, must set to timer mode.

2. The IR bit in the INT2IC may be set to “1” (interrupt requested) when the R1EDG bit is rewritten.

Refer to the paragraph 19.2.5 “Changing Interrupt Factor” in the Usage Notes Reference Book.

______

10.2 INT Interrupt

R8C/13 Datasheet(PDF) 73 Page - Renesas Technology Corp

R8C/13 Datasheet(HTML) 73 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL