| Electronic Components Datasheet Search |
|
LX2160A-RDB-B Datasheet(PDF) 51 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
LX2160A-RDB-B Datasheet(HTML) 51 Page - NXP Semiconductors |
|
51 / 116 page ![]() CPLD SW1 3V3 IRQ1_B IRQ[6:7]_B IRQ[9:11]_B LX2160A CPLD CFG_40GE_ROM CFG_MUX_EC2 CFG_SPREAD CFG_CLKEN_SLOT[1:2]_B CFG_IEEE_SRC MAX CPLDs do not have a pulldown option, so switches are implemented as shown. The CPLD inverts the signals, so that UP = ON. CPLD CPLD SW2 CLK_OUT XSPI_A_CS[0:1]_B XSPI_A_SCK SDHC2_DAT[7:6] cfg_rcw_src[1:0] cfg_eng_use[1:2] cfg_soc_use cfg_rcw_src3 cfg_eng_use0 cfg_svr[0:1] cfg_gpin[7:6] UART[1:2]_SOUT UART[1:2]_RTS_B USB1_PWRFAULT CFG_DRV SW3 SW4 LED_STAT[7:0] ASLEEP RESET_REQ_B TEST_SEL_B TBSCAN_EN_B cfg_rcw_src[2] cfg_pllcfg_b TEST_SEL_B TBSCAN_EN_B To clocks CFG_XSPI_MAP[3:0] To XSPI To PHYs CFG_MEM_WP CFG_CAN_EN_B To misc DDR_EVENT_B VDD_ALERT_B PRSNT_PROC_B PRSNT_SLOT[1:2]_B ROTATION_ERR_B THERM_WRN_B THERM_FLT_B CPU_ID[1:0] LED_FAIL LED_PASS LED_PORST LED_RSTREQ LED_ASLEEP LED_THERM SW1[1:8] SW2[1:8] SW3[1:8] SW4[1:8] I2C1_SDA I2C1_SCL CTS 218-8LPST CTS 218-8LPST CTS 218-8LPST CTS 218-8LPST CFG_XTEST LEDs of indicated colors (RED = alert) Test-point Refer to GSG for assignments SFP[2:3]_TX_FAULT SFP[2:3]_RX_LOS SFP[2:3]_MOD_ABS SFP[2:3]_TX_EN From DUT I2C port To SFP sites IRQ_FAN_B IRQ_QSFP_B IRQ_RTC_B PHY_25G_LOL SI5341_LOL_B QSFP_MOD_PRS_B QSFP_MOD_SEL_B To DUT interrupt inputs From interrupt sources From fault or alert sources Figure 30. System controller architecture (continued) The system controller is implemented in a 256-ball micro-BGA Altera CPLD, EPM2210F256C5N. The system controller is powered continuously using the 3.3 V and 1.8 V regulators, powered from the ATX PSU +5 V standby power. This allows it to control all aspects of board bring-up, including initial power sequencing. 2.19.1 System configuration The system controller uses switches to configure the target system into various modes. Switches are sampled and stored in BRDCFG and DUTCFG registers. BRDCFG registers are always active, and software may change them to result in immediate changes to the system configuration. DUTCFG registers are used to control processor configuration pins that are only sampled during PORESET_B, such as RCW_SRC in DUTCFG0. Changes to DUTCFG registers only take effect on the next reset or reconfiguration event. The following figure shows the configuration hardware arrangement. NXP Semiconductors LX2160ARDB Functional Description QorIQ LX2160A Reference Design Board Reference Manual, Rev. 4, 07/2020 Reference Manual 51 / 116 |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |