| Electronic Components Datasheet Search |
|
LX2160A-RDB-B Datasheet(PDF) 32 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
LX2160A-RDB-B Datasheet(HTML) 32 Page - NXP Semiconductors |
|
32 / 116 page ![]() Table 16. USB ports USB port Connector type Location Supported modes USB1 Type A Front panel • Host mode: Jumper J31 is shorted (default mode) • Device mode: Jumper J31 is open USB2 Micro-AB Front panel • Host mode: Jumper J33 is shorted • OTG mode: Jumper J33 is open (default mode) As described in the table above, operating modes for USB1 and USB2 ports are controlled through the J31 and J33 jumpers, respectively. The figure below shows the architecture of the LX2160ARDB USB interface. 10K 10 LX2160A 5V0 USB 3.0 type A USB1_DRVVBUS USB1_RESREF USB1_PWRFAULT USB1_VBUS “USB1” 90 W diff. imp. USB1_D_[P,M] USB1_ID USB1_TX_[P,M] USB1_RX_[P,M] <=2A <=2A USB1 NX5P3090 USB1 MODE 5V0 USB2_DRVVBUS USB2_RESREF USB2_PWRFAULT USB2_VBUS “USB2” 90 W diff. imp. USB2_DP,DM USB2_ID USB2_TXP,TXM USB2_RXP,RXM <=2A <=2A USB2 NX5P3090 USB2 MODE USB3.0 VERTICAL RIGHT-ANGLE USB 3.0 micro- AB 10K 10 NOTE: For new designs, insert a 30.1k ohm resistor in series with USBx_VBUS. See LX2160ARDB board errata E-00011 for details. Figure 19. USB architecture The USBx_DRVVBUS and USBx_PWRFAULT pins of each USB controller are connected to a programmable-current USB switch, NX5P3090UK (from NXP), for individual port management. The USB switch is powered from +5 V USB power supply. The USB1_DRVVBUS/USB2_DRVVBUS signal controls the VBUS drive for USB1/USB2 port. The USB1_PWRFAULT/ USB2_PWRFAULT signal gets power fault indications through the USB switch. The maximum allowed current consumption of a USB connected device is 2 A per channel. For new board designs based on the LX2160A processor, insert a 30.1 kΩ (±1%) resistor in series with USB1_VBUS and USB1_VBUS each. For more details, see erratum E-00011 in QorIQ LX2160A Reference Design Board Errata. NOTE Each USB connector has an LED nearby, USB1_5V and USB2_5V, which are active when the +5 V USB power supply is enabled. NXP Semiconductors LX2160ARDB Functional Description QorIQ LX2160A Reference Design Board Reference Manual, Rev. 4, 07/2020 Reference Manual 32 / 116 |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |