SST26WF080BA datasheet(7/96 Pages) MICROCHIP

7 / 96 page

 2014-2017 Microchip Technology Inc.

DS20005283C-page 7

SST26WF040B/040BA SST26WF080B/080BA

4.0

DEVICE OPERATION

The SST26WF040B/040BA and SST26WF080B/

080BA support both Serial Peripheral Interface (SPI)

bus protocol and a 4-bit multiplexed SQI bus protocol.

To provide backward compatibility to traditional SPI

Serial Flash devices, the device’s initial state after a

power-on reset is SPI mode which supports multi-I/O

(x1/x2/x4) Read/Write commands. A command instruc-

tion configures the device to SQI mode. The dataflow in

the SQI mode is similar to the SPI mode, except it uses

four multiplexed I/O signals for command, address, and

data sequence.

SQI Flash Memory supports both Mode 0 (0,0) and

Mode 3 (1,1) bus operations. The difference between

the two modes is the state of the SCK signal when the

bus master is in stand-by mode and no data is being

transferred. The SCK signal is low for Mode 0 and SCK

signal is high for Mode 3. For both modes, the Serial

Data I/O (SIO[3:0]) is sampled at the rising edge of the

SCK clock signal for input, and driven after the falling

edge of the SCK clock signal for output. The traditional

SPI protocol uses separate input (SI) and output (SO)

data signals as shown in Figure 4-1. The SQI protocol

uses four multiplexed signals, SIO[3:0], for both data in

and data out, as shown in Figure 4-2. This means the

SQI protocol quadruples the traditional bus transfer

speed at the same clock frequency, without the need

for more pins on the package.

FIGURE 4-1:

SPI PROTOCOL (TRADITIONAL 25 SERIES SPI DEVICE)

FIGURE 4-2:

SQI SERIAL QUAD I/O PROTOCOL

4.1

Device Protection

The

SST26WF040B/040BA

and

SST26WF080B/

080BA offer a flexible memory protection scheme that

allows the protection state of each individual block to be

controlled separately. In addition, the Write-Protection

Lock-Down register prevents any change of the lock sta-

tus during device operation. To avoid inadvertent writes

during power-up, the device is write-protected by default

after a power-on reset cycle. A Global Block-Protection

Unlock command offers a single command cycle that

unlocks the entire memory array for faster manufactur-

ing throughput.

For extra protection, there is an additional non-volatile

Protection register bits for each individual block. Each

of the corresponding lock-down bits are one time pro-

grammable (OTP)—once written, they cannot be

erased. Data that had been previously programmed

into these blocks cannot be altered by programming or

erase and is not reversible

4.1.1

INDIVIDUAL BLOCK PROTECTION

The SST26WF040B/040BA and SST26WF080B/

080BA have a Block-Protection register which provides

a software mechanism to write-lock the individual

memory blocks and write-lock, and/or read-lock, the

individual parameter blocks. The Block-Protection reg-

ister is 24 bits (4 Mbit) or 32 (8 Mbit) wide: two bits each

for the eight 8 KByte parameter blocks (write-lock and

read-lock), and one bit each for the remaining 32 KByte

and 64 KByte overlay blocks (write-lock). See Table 5-

6 for address range protected per register bit.

Each bit in the Block-Protection register (BPR) can be

written to a ‘1’ (protected) or ‘0’ (unprotected). For the

parameter blocks, the most significant bit is for read-lock,

and the least significant bit is for write-lock. Read-locking

the parameter blocks provides additional security for sen-

sitive data after retrieval (e.g., after initial boot). If a block

is read-locked all reads to the block return data 00H.

The Write Block-Protection Register command is a

two-cycle command which requires that Write-Enable

(WREN) is executed prior to the Write Block-Protection

20005283 F03.0

MODE 3

SCK

CE#

MODE 3

DON'T CARE

Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

MODE 0

HIGH IMPEDANCE

MSB

20005283 F04.0

MODE 3

CLK

SIO(3:0)

CE#

MODE 3

MODE 0

MSB

SST26WF080BA Datasheet(PDF) 7 Page - Microchip Technology

SST26WF080BA Datasheet(HTML) 7 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96

Datasheet Download

Link URL