 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
FT230XQ-R Datasheet(PDF) 23 Page - Future Technology Devices International Ltd. |
|
|
|||||||||||||||||||||||||||||
FT230XQ-R Datasheet(HTML) 23 Page - Future Technology Devices International Ltd. |
|
|
23 / 44 page  Copyright © Future Technology Devices International Limited 23 FT230X USB TO BASIC UART IC Version 1.4 Document No.: FT_000566 Clearance No.: FTDI# 260 6.2 Self Powered Configuration FT230X 1 2 3 4 5 SHIELD GND GND VCC GND VCC 3V3OUT USBDM USBDP VCCIO VCC(3.3-5.25V) RESET# 100nF 100nF 100nF 4.7uF + GND 4k7 10k 27R 27R GND 47pF 47pF VBUS_SENSE Figure 6.2 Self Powered Configuration Figure 6.2 illustrates the FT230X in a typical USB self powered configuration. A USB self powered device gets its power from its own power supply, VCC, and does not draw current from the USB bus. The basic rules for USB self powered devices are as follows – i) A self powered device should not force current down the USB bus when the USB host or hub controller is powered down. ii) A self powered device can use as much current as it needs during normal operation and USB suspend as it has its own power supply. iii) A self powered device can be used with any USB host, a bus powered USB hub or a self powered USB hub. The power descriptor in the internal MTP memory of the FT230X should be programmed to a value of zero (self powered). In order to comply with the first requirement above, the USB bus power (pin 1) is used to control the VBUS_Sense pin of the FT230X device. When the USB host or hub is powered up an internal 1.5kΩ resistor on USBDP is pulled up to +3.3V, thus identifying the device as a full speed device to the USB host or hub. When the USB host or hub is powered off, VBUS_Sense pin will be low and the FT230X is held in a suspend state. In this state the internal 1.5kΩ resistor is not pulled up to any power supply (hub or host is powered down), so no current flows down USBDP via the 1.5kΩ pull-up resistor. Failure to do this may cause some USB host or hub controllers to power up erratically. Figure 6.2 illustrates a self powered design which has a +3.3V to +5.25V supply. Note: 1. When the FT230X is in reset, the UART interface I/O pins are tri-stated. Input pins have internal 75kΩ pull-up resistors to VCCIO, so they will gently pull high unless driven by some external logic. |
Similar Part No. - FT230XQ-R |
|
Similar Description - FT230XQ-R |
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.COM |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
