| Electronic Components Datasheet Search |
|
MAX445C/D Datasheet(PDF) 5 Page - Maxim Integrated Products |
|
|
|||||||||||||||||||||||||||||
MAX445C/D Datasheet(HTML) 5 Page - Maxim Integrated Products |
|
5 / 8 page ![]() IOUT The MAX445’s output is an open collector of a cascode amplifier. This output is designed to work with nominal output supplies of VAA = +75V. The high-voltage supply must be greater than any applied VCB voltage for proper operation. The MAX445 sinks up to 250mA. Optimum performance into a capacitive load can be achieved when an impedance-matching network is used. VCB The output stage consists of a common-base, high-voltage stage and a high-speed, low-voltage current amplifier in a cascode arrangement. The VCB input is the base connec- tion to the common-base device of this stage. Be sure to provide a stable DC voltage at this pin of nominally +10V. High-frequency compensation at this input is required to avoid output oscillations. Use a series 24 Ω resistor to sup- ply, shunted with a 10pF capacitor to ground (Figure 1). Smaller values of this RC combination will improve output rise/fall times, but can cause output oscillations. Power Supplies +10V and -10.5V supplies are required for proper opera- tion. These supplies can be set to ±12V for conve- nience, however this will add additional component power dissipation. The high-voltage supply, VAA, can be any voltage between VCB + 10V and VCB + 65V. VEEO (pin 21) is the negative supply to the output stage and must be DC connected to VEE (pins 8 and 9), the most negative voltage applied to the device. However, VEEO must be decoupled from VEE to prevent output oscillations. A ferrite bead and separate 0.1µF decou- pling capacitors, as shown in Figure 1, will provide appropriate decoupling. Power-Supply Sequencing Power-supply sequencing is important to avoid internal device latchup. To avoid sequencing problems, external diodes should be placed from VEE to ground, from ground to VCC, and from VCC to the output supply (VAA), as shown in Figure 1. With diodes used as shown, spe- cial power-supply sequencing is not required. CRT Arc Protection The MAX445 must be protected from electrostatic dis- charge (“arcs”) from the CRT. It is recommended that the output be clamped with a low-capacitance (less than 2pF) diode to the VAA supply. The peak current-handling capability required of the diode is a function of the CRT arc characteristics, but typically should be 1A or more, such as Philips BAV20 or Hitachi 1SS91. For additional information regarding arc protection, contact Maxim’s applications department. Impedance Matching Network For maximum speed from the MAX445, be sure to “match” the output to the CRT. Figure 1’s typical connec- tion diagram shows a network (including parasitic reac- tances) associated with arc protection devices, CRT wiring and grid structure, and load resistors. These para- sitic reactances are all detrimental to good transient response and should be minimized as much as possible. CL is the grid-to-cathode capacitance of the CRT, plus any parasitic capacitance to ground associated with the cathode structure. This capacitance varies from tube- type to tube-type over the 4pF to 12pF range. In Figure 1, LS is the inductance of the lead from the amplifier board to the CRT cathode and the return path from the grid to circuit ground. A wire in free space has an inductance of 20nH/inch to 25nH/inch. With care, the total path through the CRT gun can be kept at 1.5 to 2 inches, such that LS ranges from 30nH to 50nH. Excessive lead length will cause undesirable overshoot and ringing in the transient response. The peaking networks assume that 2pF of parasitic capacitance is associated with the CRT arc protection diode connected at the junction of L3 and L1. Lr is the parasitic inductance of the load resistor, RL. In some cases, CR may be needed to improve step response. RS is a damping resistor in series with the CRT grid. It also provides current limiting in the event of CRT arcing. The equations for determining optimum peaking net- work values are as follows: L1 = (RL)2 (CL) / 4 L2 = 3(RL)2 (CL) / 4 CB = CL / 5 RS = RL / 2 L3 = k3 (RL)2 [2.5 x 10-12] CR (optional) = Lr / (2RL2) k3 is an empirically determined factor increasing with CL and varying from 0 for CL ~ 2pF to 1 for CL ~ 12pF. However, L3 >100nH will compromise large-signal per- formance. Table 1 shows peaking networks for the nominal load, RL = 200 Ω (and RS = 100Ω). Optimum peaking depends on board layout and CRT construction. The values given by these equations should be used as starting points for empirically deter- mining optimum values. Low-Cost, High-Resolution, 200MHz Video CRT Driver _______________________________________________________________________________________ 5 |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |