AM6412...ALV datasheet(15/244 Pages) TI

15 / 244 page

5. TYPE: Signal type and direction:

• I = Input

• O = Output

• OD = Output, with open-drain output function

• IO = Input, Output, or simultaneously Input and Output

• IOD = Input, Output, or simultaneously Input and Output, with open-drain output function

• IOZ = Input, Output, or simultaneously Input and Output, with three-state output function

• OZ = Output with three-state output function

• A = Analog

• PWR = Power

• GND = Ground

• CAP = LDO Capacitor.

6. DSIS: The deselected input state (DSIS) indicates the state driven to the subsystem input (logic "0", logic

"1", or "pad" level) when the pin multiplexed signal function is not selected by MUXMODE.

• 0: Logic 0 driven to the subsystem input.

• 1: Logic 1 driven to the subsystem input.

• pad: Logic state of the pad is driven to the subsystem input.

• An empty box means Not Applicable.

7. BALL STATE DURING RESET RX/TX/PULL: State of the terminal while MCU_PORz is asserted, where RX

defines the state of the input buffer, TX defines the state of the output buffer, and PULL defines the state of

internal pull resistors:

• RX (Input buffer)

– Off: The input buffer is disabled.

– On: The input buffer is enabled.

• TX (Output buffer)

– Off: The output buffer is disabled.

– Low: The output buffer is enabled and drives VOL.

• PULL (Internal pull resistors)

– Off: Internal pull resistors are turned off.

– Up: Internal pull-up resistor is turned on.

– Down: Internal pull-down resistor is turned on.

• An empty box means Not Applicable.

8. BALL STATE AFTER RESET RX/TX/PULL: State of the terminal after MCU_PORz is deasserted, where

RX defines the state of the input buffer, TX defines the state of the output buffer, and PULL defines the state

of internal pull resistors:

• RX (Input buffer)

– Off: The input buffer is disabled.

– On: The input buffer is enabled.

• TX (Output buffer)

– Off: The output buffer is disabled.

– SS: The subsystem selected with MUXMODE determines the output buffer state.

• PULL (Internal pull resistors)

– Off: Internal pull resistors are turned off.

– Up: Internal pull-up resistor is turned on.

– Down: Internal pull-down resistor is turned on.

• An empty box means Not Applicable.

9. MUX MODE AFTER RESET: The value found in this column defines the default pin multiplexed signal

function after MCU_PORz is deasserted.

An empty box means Not Applicable.

www.ti.com

AM6442, AM6441, AM6421, AM6412, AM6411

SPRSP56D – JANUARY 2021 – REVISED JULY 2022

Submit Document Feedback

Product Folder Links: AM6442 AM6441 AM6421 AM6412 AM6411

AM6412...ALV Datasheet(PDF) 15 Page - Texas Instruments

AM6412...ALV Datasheet(HTML) 15 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL