TLV9041UIDBVR datasheet(20/72 Pages) TI

20 / 72 page

8.3 Feature Description

8.3.1 Operating Voltage

The TLV904x series of operational amplifiers is fully specified and ensured for operation from 1.2 V to 5.5 V.

In addition, many specifications apply from –40°C to 125°C. Parameters that vary significantly with operating

voltages or temperature are provided in Section 7.8. It is highly recommended to bypass power-supply pins with

at least 0.01-μF ceramic capacitors.

8.3.2 Rail-to-Rail Input

The input common-mode voltage range of the TLV904x series extends to either supply rails. This is true even

when operating at the ultra-low supply voltage of 1.2 V, all the way up to the standard supply voltage of 5.5 V.

This performance is achieved with a complementary input stage: an N-channel input differential pair in parallel

with a P-channel differential pair. Refer to Section 8.2 for more details.

For most amplifiers with a complementary input stage, one of the input pairs, usually the P-channel input pair,

is designed to deliver slightly better performance in terms of input offset voltage, offset drift over the N-channel

pair. Consequently, the P-channel pair is designed to cover the majority of the common mode range with the

N-channel pair slated to slowly take over at a certain threshold voltage from the positive rail. Just after the

threshold voltage, both the input pairs are in operation for a small range referred to as the transition region.

Beyond this region, the N-channel pair completely takes over. Within the transition region, PSRR, CMRR, offset

voltage, offset drift, and THD can be degraded compared to device operation outside this region. Hence, most

applications generally prefer operating in the P-channel input range where the performance is slightly better.

For the TLV904x, the P-channel pair is typically active for input voltages from the negative rail to (V+) – 0.4

V and the N-channel pair is typically active for input voltages from the positive supply to (V+) – 0.4 V. The

transition region occurs typically from (V+) – 0.5 V to (V+) – 0.3 V, in which both pairs are on. These voltage

levels mentioned above can vary with process variations associated with threshold voltage of transistors. In

the TLV904x, 200-mV transition region mentioned above can vary up to 200 mV in either direction. Thus, the

transition region (both stages on) can range from (V+) – 0.7 V to (V+) – 0.5 V on the low end, up to (V+) – 0.3 V

to (V+) – 0.1 V on the high end.

Recollecting the fact that a P-channel input pair usually offers better performance over a N-channel input pair,

the TLV904x is designed to offer a much wider P-channel input pair range, in comparison to most complimentary

input amplifiers in the industry. A side by side comparison of the TLV904x and the TLV900x is provided below.

Note, that the TLV900x guarantees P-channel pair operation only until 1.4 V from the positive rail while the

TLV904x guarantees P-channel pair operation all the way till 0.7 V from the positive rail. This additional 700mV

of P-channel input pair range for the TLV904x is particularly useful when operating at lower supply voltages (1.2

V, 1.8 V etc) where the P-channel input range usually gets limited to a great extent.

Thus the wide common mode swing of input signal can be accommodated more easily within the P-channel

input pair of the TLV904x, while likely avoiding the transition region, thereby maintaining linearity.

TLV9041, TLV9042, TLV9044

SBOS836G – MARCH 2020 – REVISED MARCH 2022

www.ti.com

Submit Document Feedback

Product Folder Links: TLV9041 TLV9042 TLV9044

TLV9041UIDBVR Datasheet(PDF) 20 Page - Texas Instruments