AD8278ARMZ-R7 datasheet(3/24 Pages) AD

3 / 24 page

AD8278

Rev. 0 | Page 3 of 24

SPECIFICATIONS

VS = ±5 V to ±15 V, VREF = 0 V, TA = 25°C, RL = 10 kΩ connected to ground, G = ½ difference amplifier configuration, unless

otherwise noted.

Table 2.

Parameter

Conditions

G = ½

Unit

Grade B

Grade A

Min

Typ

Max

Min

Typ

Max

INPUT CHARACTERISTICS

System Offset1

100

250

μV

vs. Temperature

TA = −40°C to +85°C

100

250

μV

Average Temperature

Coefficient

TA = −40°C to +85°C

0.3

μV/°C

vs. Power Supply

VS = ±5 V to ±18 V

2.5

μV/V

Common-Mode Rejection

Ratio (RTI)

VS = ±15 V, VCM = ±27 V,

RS = 0 Ω

Input Voltage Range2

−3(VS + 0.1)

+3(VS − 1.5)

−3(VS + 0.1)

+3(VS − 1.5)

Impedance3

Differential

120

kΩ

Common Mode

kΩ

DYNAMIC PERFORMANCE

Bandwidth

MHz

Slew Rate

1.1

1.4

1.1

1.4

V/μs

Settling Time to 0.01%

10 V step on output,

CL = 100 pF

μs

Settling Time to 0.001%

μs

GAIN

Gain Error

0.005

0.02

0.01

0.05

Gain Drift

TA = −40°C to +85°C

ppm/°C

Gain Nonlinearity

VOUT = 20 V p-p

ppm

OUTPUT CHARACTERISTICS

Output Voltage Swing4

VS = ±15 V, RL = 10 kΩ

TA = −40°C to +85°C

−VS + 0.2

+VS − 0.2

−VS + 0.2

+VS − 0.2

Short-Circuit Current Limit

±15

Capacitive Load Drive

200

NOISE5

Output Voltage Noise

f = 0.1 Hz to 10 Hz

1.4

μV p-p

f = 1 kHz

nV/√Hz

POWER SUPPLY

Supply Current6

200

μA

vs. Temperature

TA = −40°C to +85°C

250

μA

Operating Voltage Range7

±2

±18

±2

±18

TEMPERATURE RANGE

Operating Range

−40

+125

−40

+125

°C

1 Includes input bias and offset current errors, RTO (referred to output)

2 The input voltage range may also be limited by absolute maximum input voltage or by the output swing. See the Input Voltage Range section in the Theory of

Operation for details.

3 Internal resistors are trimmed to be ratio matched and have ±20% absolute accuracy.

4 Output voltage swing varies with supply voltage and temperature. See Figure 20 through Figure 23 for details.

5 Includes amplifier voltage and current noise, as well as noise from internal resistors.

6 Supply current varies with supply voltage and temperature. See Figure 24 and Figure 26 for details.

7 Unbalanced dual supplies can be used, such as −VS = −0.5 V and +VS = +2 V. The positive supply rail must be at least 2 V above the negative supply and reference

voltage.

AD8278ARMZ-R7 Datasheet(PDF) 3 Page - Analog Devices

AD8278ARMZ-R7 Datasheet(HTML) 3 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Datasheet Download

Link URL