CMS6416LAH datasheet(9/46 Pages) FIDELIX

9 / 46 page

Rev1.3, Nov. 2005

CMS6416LAx-75xx

7-6-5-4-3-2-1-0

7-0-1-2-3-4-5-6

1 1 1

4-5-6-7-0-1-2-3

1 0 0

5-4-7-6-1-0-3-2

5-6-7-0-1-2-3-4

1 0 1

6-7-4-5-2-3-0-1

6-7-0-1-2-3-4-5

1 1 0

1-0-3-2-5-4-7-6

1-2-3-4-5-6-7-0

0 0 1

2-3-0-1-6-7-4-5

2-3-4-5-6-7-0-1

0 1 0

3-2-1-0-7-6-5-4

3-4-5-6-7-0-1-2

0 1 1

3-2-1-0

3-0-1-2

1 1

A2 A1 A0

0-1-2-3-4-5-6-7

0 0 0

0-1-2-3

0 0

1-0-3-2

1-2-3-0

0 1

2-3-0-1

1 0

0-1

1-0

A1 A0

Not supported

Bn, Bn+1, Bn+2…..Bn,…

n=A0-A8(location 0-y)

Full Page(y)

Type=Interleaved

Type=Sequential

Order of Accesses within a Burst

Starting Column Address

Burst Length

Table 2. Burst Length Definition.

Operating Mode

The normal operating mode is selected by setting M7 and M8

to zero; the other combinations of values for M7 and M8 are

reserved for future use and/or test modes. The programmed

burst length applies to both READ and WRITE bursts.Test

modes and reserved states should not be used because

unknown operation or incompatibility with future versions may

result.

CAS Latency

The CAS latency is the delay, in clock cycles, between the

registration of a READ command and the availability of the first

piece of output data. The latency can be set to one, two,

or three clocks. If a READ command is registered at clock

edge r, and the latency is q clocks, the data will be available

by clock edge r + q. The DQs will start driving as a result of

the clock edge one cycle earlier (r + q- 1), and provided that

the relevant access times are met, the data will be valid by

clock edge r + q. For example, assuming that the clock cycle

time is such that all relevant access times are met, if a READ

command is registered at T0 and the latency is programmed

to two clocks, the DQs will start driving after T1 and the data

will be valid by T2, as shown in Figure 2.

Reserved states should not be used as unknown operation or

incompatibility with future versions may result.

Write Burst Mode

When M9=0, the burst length programmed via M0-M2 applies to

both READ and WRITE bursts; when M9=1, the programmed

burst length applies to READ bursts, but write accesses are

single-location (non-burst) accesses.

CMS6416LAH Datasheet(PDF) 9 Page - FIDELIX

CMS6416LAH Datasheet(HTML) 9 Page - FIDELIX

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46

Datasheet Download

Link URL