HD6432138SW datasheet(703/1061 Pages) RENESAS

703 / 1061 page

Section 22 ROM (H8S/2138 F-ZTAT A-Mask Version, H8S/2134 F-ZTAT A-Mask Version)

Rev. 4.00 Jun 06, 2006 page 649 of 1004

REJ09B0301-0400

22.7.3

Erase Mode

Flash memory erasing should be performed block by block following the procedure shown in the

erase/erase-verify flowchart (single-block erase) shown in figure 22.13.

The wait times (x, y, z,

α, β, γ, ε, η, θ) after setting/clearing individual bits in flash memory

control registers 1 and 2 (FLMCR1, FLMCR2) and the maximum number of erase (N) are shown

in section 25, Electrical Characteristics, Flash Memory Characteristics.

To perform data or program erasure, make a 1 bit setting for the flash memory area to be erased in

erase block register 1 or 2 (EBR1 or EBR2) at least (x) µs after setting the SWE bit to 1 in flash

memory control register 1 (FLMCR1). Next, the watchdog timer is set to prevent overerasing in

the event of program runaway, etc. Set a value greater than (y + z +

α + β) ms as the WDT

overflow period. After this, preparation for erase mode (erase setup) is carried out by setting the

ESU bit in FLMCR2, and after the elapse of (y) µs or more, the operating mode is switched to

erase mode by setting the E bit in FLMCR1. The time during which the E bit is set is the flash

memory erase time. Ensure that the erase time does not exceed (z) ms.

Note:

With flash memory erasing, preprogramming (setting all data in the memory to be erased

to 0) is not necessary before starting the erase procedure.

22.7.4

Erase-Verify Mode

In erase-verify mode, data is read after memory has been erased to check whether it has been

correctly erased.

After the elapse of the erase time, erase mode is exited (the E bit in FLMCR1 is cleared, then the

ESU bit in FLMCR2 is cleared at least (

α) µs later), the watchdog timer is cleared after the elapse

of (

β) µs or more, and the operating mode is switched to erase-verify mode by setting the EV bit in

FLMCR1. Before reading in erase-verify mode, a dummy write of H'FF data should be made to

the addresses to be read. The dummy write should be executed after the elapse of (

γ) µs or more.

When the flash memory is read in this state (verify data is read in 16-bit units), the data at the

latched address is read. Wait at least (

ε) µs after the dummy write before performing this read

operation. If the read data has been erased (all 1), a dummy write is performed to the next address,

and erase-verify is performed. If the read data has not been erased, set erase mode again, and

repeat the erase/erase-verify sequence in the same way. However, ensure that the erase/erase-

verify sequence is not repeated more than (N) times. When verification is completed, exit erase-

verify mode, and wait for at least (

η) µs. If erasure has been completed on all the erase blocks,

clear the SWE bit in FLMCR1, and wait (

θ) µs. If there are any unerased blocks, make a 1 bit

setting in EBR1 or EBR2 for the flash memory area to be erased, and repeat the erase/erase-verify

sequence in the same way.

HD6432138SW Datasheet(PDF) 703 Page - Renesas Technology Corp

HD6432138SW Datasheet(HTML) 703 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL