Overview

The D10 Expert Sensor is a high-performance plastic fiber-optic sensor whose many

configuration (TEACH-mode) options make it suitable for demanding applications. Even

with all its features, it is extremely easy to use. Advanced 16-bit microcontroller

technology makes this possible.

The D10 Expert provides high-performance sensing in low-contrast applications. Expert

TEACH and setup options provide static, dynamic and single-point programming plus

manual fine adjustment, remote programming and push button lockout. Its slender,

stylized housing has a large digital display visible beneath a clear cover for easy

programming and status monitoring during operation. The sensor mounts directly to

standard 35 mm DIN rail or using the supplied mounting bracket.

The sensor features two outputs with independent setpoints: one of two analog choices,

depending on model, and one discrete (NPN or PNP, also depending on model). Built-in

crosstalk avoidance protocol provides trouble-free operation for multiple sensors in one

area.

For emitter and receiver port locations, see Installation on page 13

dynamic

static

Output

Indicators

Output Select

Indicators

4-Digit

Display

Light/Dark

Operate, Clock

and Lock Icons

Programming

Push Buttons

Figure 1. D10 Features

Programming Options

Light/Dark Operate Selection

Toggle to select the condition for which each output will conduct: when the target is present or when the target is absent.

OFF-Delay Timing Selection

Programmable OFF-delay pulse stretcher: 0, 2, 5, 10, 15, 20, 30, 40, 60, 80, or 100 ms

Analog Outputs: OFF-delay acts as a smoothing function

Display Selection

Discrete Output: Raw signal value or % excess signal

Analog Output: Raw signal value or analog value (0 to 10V dc or 4 to 20 mA)

Power Level/Speed Selection

Super High-Speed (SHS)

High-Speed (HS)

High-Power (HP)

Super High-Power (SHP)

Response*

50 μs

200 μs

1 ms

2.5 ms

Repeatability

25 μs

50 μs

75 μs

100 μs

Max Range*

Fiber

Red 680 nm

Green 525 nm

Red 680 nm

Green 525 nm

Red 680 nm

Green 525 nm

Red 680 nm

Green 525 nm

PIT16U

20 mm

9 mm

30 mm

9 mm

55 mm

13 mm

90 mm

16 mm

PIT26U

100 mm

40 mm

150 mm

40 mm

250 mm

55 mm

400 mm

70 mm

PIT46U

300 mm

100 mm

550 mm

100 mm

1000 mm

160 mm

1200 mm

180 mm

PIT66U

600 mm

180 mm

1000 mm

180 mm

1700 mm

280 mm

2400 mm

320 mm

PBT16U

6 mm

**

10 mm

**

18 mm

3 mm

30 mm

3.5 mm

PBT26U

30 mm

12 mm

50 mm

12 mm

100 mm

20 mm

150 mm

25 mm

PBT46U

100 mm

30 mm

175 mm

30 mm

250 mm

42 mm

300 mm

60 mm

PBT66U

175 mm

55 mm

250 mm

55 mm

400 mm

80 mm

475 mm

100 mm

Tracking Feature

Sets Output 2 to identical settings as Output 1; Output 2 settings can then be revised as desired (see Advanced Setup on page 11).

Factory Default Settings

The following settings are preset at the factory; revert sensor to factory defaults using Advanced Setup procedure ( Advanced Setup on page 11).

•

Light operate (LO)

•

No OFF-delay (t 0)

•

Raw signal value (1234)

•

Output 1 displayed

•

High Speed (HS); 200 μs response

•

Maximum power setting

•

Analog: full scale

•

Discrete: switchpoint positioned at

middle of range

* Diffuse mode performance based on 90% reflectance white test card.

** ø0.010" bifurcated fiber not recommended in these speed settings. Contact Banner Applications for more information.

Sensor Programming

Programming Procedures: Two push buttons, Dynamic (+) and Static (-), may be used to access and set programming parameters. For

remote programming, connect a switch or digital input to the gray wire; length of the individual pulses is equal to the value T:

0.04 seconds ≤ T ≤ 0.8 seconds

2

www.bannerengineering.com - Tel: +1-763-544-3164

P/N 65448 Rev. G