8001L-R20-R Price, Distributor, Stock

Key Specifications, Power Output: 14 dBm P1dB, Frequency, Min: 10 MHz, Frequency, Max: 6 GHz, Gain: 14.5 dB, Noise Figure, Max: 5.5 dB, Noise Figure, Typ: 4.5 dB, RF Input VSWR, Max: 2, Voltage, DC Min: 9 Volts, Voltage, DC Max: 15 Volts, Connector Series: SMA. 14 dBm P1dB, 10 MHz to 6 GHz, Gain Block Amplifier, 14.5 dB Gain, 26 dBm IP3, 4.5 dB NF, SMA. PE15A8001 RF gain block amplifier from Pasternack is featured in our extensive in-stock RF amplifier selection. Our connectorized gain block RF amplifier uses SMA connectors. This SMA gain block amplifier has a minimum frequency of 10 MHz, a maximum frequency of 6 GHz and a typical gain of 14.5 dB. Our radio frequency gain block amp PE15A8001 is part of over 40,000 RF, microwave and millimeter wave components available from Pasternack. This coaxial gain block amplifier can ship worldwide the same day of the purchase as with our other available RF parts.

1 : $1,030.0
5 : $988.8
10 : $947.6

PE3C8001-50CM

Pasternack Enterprises

Key Specifications, Connector 1 Series: N, Connector 1 Gender: Male, Connector 1 Polarity: Standard, Connector Angle 1: Straight, Connector 1 Impedance: 50 Ohm, Connector 2 Series: N, Connector 2 Gender: Female, Connector 2 Polarity: Standard, Connector Angle 2: Straight, Connector 2 Impedance: 50 Ohm, Connector 1 Body Material: Brass, Connector 1 Body Plating: Tri-Metal, RF Cable Part Number: TFT-5G-402, RF Cable Type: TFT-5G-402, RF Cable Impedance: 50 Ohm, Length, Max: 19.68 inches. N Male to N Female Low PIM Cable 50 CM Length Using TFT-5G-402 Coax Using Times Microwave Components., Radio frequency assembly N male to N female low PIM cable 50 cm length using TFT-5G-402 coax using Times Microwave components from Pasternack is part of one of the largest selections of same-day ship coaxial cables for RF, microwave and millimeter wave interconnect solutions. Pasternack low PIM (Passive Intermodulation, also called Intermod for short) coaxial cable assembly products are used in applications requiring high quality, such as laboratory RF test and measurement, rugged and designed for defense/military, telecom antenna tower component jumper connection, production environments, general use, etc. The N male to N female low PIM cable 50 cm length using TFT-5G-402 coax using Times Microwave components, like our other Pasternack coaxial cable assemblies, will ship the same day, and any custom type N to type N cable assembly orders will ship the same business day as well. Pasternack RF coax low PIM cable assembly is built with a type N cable connection on one end and a type N cable connection on the other. Our low PIM type N to type N cable assembly has a male gender on end 1 and a female on end 2. PE3C8001-50CM can also be known as a low PIM type N plug to type N jack cable assembly and will be shipped the same day as it is purchased. This flexible RF cable assembly with a 0.808-inch diameter has copper as the cable's inner conducting material and PTFE dielectric type. type N low PIM cable assemblies from Pasternack are ideal for applications including indoor and outdoor use and plenum rated applications. The minimum bend radius for this cable is 0.75 inches, allowing for a single bend without damaging the cable. Our PE3C8001-50CM RF cable has a FEP jacket of 0.160-inch diameter. This radio frequency cable assembly can withstand temperatures ranging from -40 to 125 degrees C. The flexible RF cable has an in-series connection. This cable assembly has a typical propagation velocity of 76% and a minimum RF shielding of 80 dB. Our type N male to type N female cable has a maximum VSWR of 1.4:1. Type N plug to type N jack cable assembly PE3C8001-50CM is built with TFT-5G-402 which is a flexible coax type. The Pasternack low passive intermodulation flexible type N cable assembly is manufactured with type N to type N cable connectors, has a 50 Ohm impedance, and is double shielded. Both the connectors have a solder/solder attachment method and a brass body. Additional dimensions, specifications and CAD drawings for this low PIM RF cable are available on our downloadable PDF datasheet. PE3C8001-50CM can also be used in the other direction and will be a type N female to type N male cable assembly if the opposite connectivity is required. Low PIM type N plug to type N jack cable assembly is just one of more than one million in-stock RF products available. Pasternack is where to buy a high quality type N to type N cable assembly for quick shipment worldwide. Variations of type N cable assemblies can also be built and will ship on the same day as well, search this website or contact us for assistance. High quality custom RF cable assembly products for microwave and millimeter wave radio transmitter receiver, antenna jumper, component interconnection and more for RF test & measurement labs, rugged and MIL-STD designed military/defense, aerospace, telecom, phase stable, phase and delay matching, outdoor and harsh environment and other radio frequency applications can be manufactured. For further information on similar products, our expert technical support and trained sales team can get you the ideal type N to type N low PIM RF cable assembly as per your requirements.

1 : $78.19
25 : $74.28
50 : $70.37
100 : $67.24

PE3W16800-12

Pasternack Enterprises

Key Specifications, Connector 1 Series: SHV, Connector 1 Gender: Jack, Connector 1 Polarity: Standard, Connector Angle 1: Straight, Connector 1 Impedance: 50 Ohm, Connector 2 Series: F, Connector 2 Gender: Male, Connector 2 Polarity: Standard, Connector Angle 2: Straight, Connector 2 Impedance: 75 Ohm, Connector 1 Body Material: Brass, Connector 1 Body Plating: Tinned Copper, RF Cable Part Number: RG59B/U, RF Cable Type: RG59, RF Cable Impedance: 75 Ohm, Length, Max: 12 inches. 50 Ohm SHV Jack to 75 Ohm F Male Cable 12 Inch Length Using 75 Ohm RG59 Coax., Radio frequency assembly 50 Ohm SHV jack to 75 Ohm F male cable 12 inch length using 75 Ohm RG59 coax from Pasternack is part of one of the largest selections of same-day ship coaxial cables for RF, microwave and millimeter wave interconnect solutions. Pasternack coaxial cable assembly products are used in applications requiring high quality, such as laboratory RF test and measurement, rugged and designed for defense/military, telecom antenna tower component jumper connection, production environments, general use, etc. The 50 Ohm SHV jack to 75 Ohm F male cable 12 inch length using 75 Ohm RG59 coax, like our other Pasternack coaxial cable assemblies, will ship the same day, and any custom SHV to type F cable assembly orders will ship the same business day as well. Pasternack RF coax cable assembly is built with a SHV cable connection on one end and a type F cable connection on the other. Our SHV to type F cable assembly has a jack gender on end 1 and a male on end 2. PE3W16800-12 can also be known as a SHV female to type F plug cable assembly and will be shipped the same day as it is purchased. This flexible RF cable assembly with a 0.5-inch diameter has copper clad steel as the cable's inner conducting material and PE dielectric type. Our PE3W16800-12 RF cable has a PVC (NC) jacket of 0.242-inch diameter. This radio frequency cable assembly can withstand temperatures ranging from -25 to 70 degrees C. The flexible RF cable has a between series connection. Our SHV jack to type F male cable has a maximum VSWR of 1.4:1. SHV female to type F plug cable assembly PE3W16800-12 is built with RG59 which is a flexible coax type. The Pasternack flexible SHV cable assembly is manufactured with SHV to type F cable connectors, has a 50 Ohm impedance, and is single shielded. Both the connectors have a crimp/solder attachment method and a brass body. Additional dimensions, specifications and CAD drawings for this RF cable are available on our downloadable PDF datasheet. PE3W16800-12 can also be used in the other direction and will be a type F male to SHV jack cable assembly if the opposite connectivity is required. SHV female to type F plug cable assembly is just one of more than one million in-stock RF products available. Pasternack is where to buy a high quality SHV to type F cable assembly for quick shipment worldwide. Variations of SHV and type F cable assemblies can also be built and will ship on the same day as well, search this website or contact us for assistance. High quality custom RF cable assembly products for microwave and millimeter wave radio transmitter receiver, antenna jumper, component interconnection and more for RF test & measurement labs, rugged and MIL-STD designed military/defense, aerospace, telecom, phase stable, phase and delay matching, outdoor and harsh environment and other radio frequency applications can be manufactured. For further information on similar products, our expert technical support and trained sales team can get you the ideal SHV to type F RF cable assembly as per your requirements.

1 : $97.39
25 : $92.52
50 : $87.65
100 : $83.76

PE3800-18

Pasternack Enterprises

Key Specifications, Connector Series 1: SMA, Connector Gender 1: Male, Connector Polarity 1: Standard, Connector Angle 1: Right Angle, Connector Mount Method 1: None, Connector Impedance 1: 50 Ohm, Connector Series 2: SMA, Connector Gender 2: Female, Connector Polarity 2: Standard, Connector Angle 2: Straight, Connector Mount Method 2: Bulkhead, Connector Impedance 2: 50 Ohm, RF Cable Part Number: RG223/U, RF Cable Type: RG223, RF Cable Impedance: 50 Ohm, Length: 18 inches. SMA Male Right Angle to SMA Female Bulkhead Cable 18 Inch Length Using RG223 Coax., Radio frequency assembly SMA male right angle to SMA female bulkhead cable 18 inch length using RG223 coax from Pasternack is part of the largest selections of same-day ship coaxial cables for RF, microwave and millimeter wave interconnect solutions. Pasternack coaxial cable assembly products are used in applications requiring high quality such as laboratory RF test and measurement, rugged and designed for defense / military, telecom antenna tower component jumper connection, production environments, general use, etc. SMA male right angle to SMA female bulkhead cable 18 inch length using RG223 coax, like our other Pasternack coaxial cable assemblies, will ship the same day and any custom SMA to SMA cable assembly orders will ship same day as well. Pasternack RF coax cable assembly is built with right angle SMA cable connection on one end and SMA bulkhead cable connection on the other. Our right angle SMA to SMA cable assemblies have a male gender on end 1 and female on end 2. This SMA to SMA cable is a male to female coax assembly, PE3800-18, can also be known as a right angle SMA plug to SMA jack cable assembly and will be shipped same-day as it is purchased. SMA plug to SMA jack cable assembly PE3800-18 is built with RG223 which is a flexible coax type. The Pasternack flexible SMA cable assembly is manufactured with right angle SMA to SMA cable connectors, has a 50 Ohm impedance and is double shielded. RF specs on this 12.4 GHz maximum frequency SMA right angle male to SMA female bulkhead cable are located on the specifications PDF datasheet on this page along with CAD drawing and dimensions. PE3800-18 can also be used in the other direction and will be SMA female bulkhead to right angle SMA male cable assembly if the opposite connectivity is required. SMA right angle plug to SMA jack bulkhead cable assembly is just one of more than 45,000 in-stock RF products available. Pasternack is where to buy a high quality SMA to SMA cable assembly for quick shipment worldwide. Variations of SMA cable assemblies can also be built and will ship same-day as well, search this website or contact us for assistance. High quality custom RF cable assembly products for microwave and millimeter wave radio transmitter receiver, antenna jumper, component inter-connection and more for RF test & measurement labs, rugged and MIL-STD designed military / defense, aerospace, telecom, phase stable, phase and delay matching, outdoor and harsh environment and other radio frequency applications can be manufactured. For all these reasons and more, Pasternack is one of the best websites where to find and buy quality RF cable assemblies like this SMA male right angle to SMA female bulkhead cable 18 inch length using RG223 coax.

1 : $68.49
25 : $65.07
50 : $61.64
100 : $58.9

PE3C8001-48

Pasternack Enterprises

Key Specifications, Connector 1 Series: N, Connector 1 Gender: Male, Connector 1 Polarity: Standard, Connector Angle 1: Straight, Connector 1 Impedance: 50 Ohm, Connector 2 Series: N, Connector 2 Gender: Female, Connector 2 Polarity: Standard, Connector Angle 2: Straight, Connector 2 Impedance: 50 Ohm, Connector 1 Body Material: Brass, Connector 1 Body Plating: Tri-Metal, RF Cable Part Number: TFT-5G-402, RF Cable Type: TFT-5G-402, RF Cable Impedance: 50 Ohm, Length, Max: 48 inches. N Male to N Female Low PIM Cable 48 Inch Length Using TFT-5G-402 Coax Using Times Microwave Components., Radio frequency assembly N male to N female low PIM cable 48 inch length using TFT-5G-402 coax using Times Microwave components from Pasternack is part of one of the largest selections of same-day ship coaxial cables for RF, microwave and millimeter wave interconnect solutions. Pasternack low PIM (Passive Intermodulation, also called Intermod for short) coaxial cable assembly products are used in applications requiring high quality, such as laboratory RF test and measurement, rugged and designed for defense/military, telecom antenna tower component jumper connection, production environments, general use, etc. The N male to N female low PIM cable 48 inch length using TFT-5G-402 coax using Times Microwave components, like our other Pasternack coaxial cable assemblies, will ship the same day, and any custom type N to type N cable assembly orders will ship the same business day as well. Pasternack RF coax low PIM cable assembly is built with a type N cable connection on one end and a type N cable connection on the other. Our low PIM type N to type N cable assembly has a male gender on end 1 and a female on end 2. PE3C8001-48 can also be known as a low PIM type N plug to type N jack cable assembly and will be shipped the same day as it is purchased. This flexible RF cable assembly with a 0.808-inch diameter has copper as the cable's inner conducting material and PTFE dielectric type. type N low PIM cable assemblies from Pasternack are ideal for applications including indoor and outdoor use and plenum rated applications. The minimum bend radius for this cable is 0.75 inches, allowing for a single bend without damaging the cable. Our PE3C8001-48 RF cable has a FEP jacket of 0.160-inch diameter. This radio frequency cable assembly can withstand temperatures ranging from -40 to 125 degrees C. The flexible RF cable has an in-series connection. This cable assembly has a typical propagation velocity of 76% and a minimum RF shielding of 80 dB. Our type N male to type N female cable has a maximum VSWR of 1.4:1. Type N plug to type N jack cable assembly PE3C8001-48 is built with TFT-5G-402 which is a flexible coax type. The Pasternack low passive intermodulation flexible type N cable assembly is manufactured with type N to type N cable connectors, has a 50 Ohm impedance, and is double shielded. Both the connectors have a solder/solder attachment method and a brass body. Additional dimensions, specifications and CAD drawings for this low PIM RF cable are available on our downloadable PDF datasheet. PE3C8001-48 can also be used in the other direction and will be a type N female to type N male cable assembly if the opposite connectivity is required. Low PIM type N plug to type N jack cable assembly is just one of more than one million in-stock RF products available. Pasternack is where to buy a high quality type N to type N cable assembly for quick shipment worldwide. Variations of type N cable assemblies can also be built and will ship on the same day as well, search this website or contact us for assistance. High quality custom RF cable assembly products for microwave and millimeter wave radio transmitter receiver, antenna jumper, component interconnection and more for RF test & measurement labs, rugged and MIL-STD designed military/defense, aerospace, telecom, phase stable, phase and delay matching, outdoor and harsh environment and other radio frequency applications can be manufactured. For further information on similar products, our expert technical support and trained sales team can get you the ideal type N to type N low PIM RF cable assembly as per your requirements.

1 : $88.89
25 : $84.45
50 : $80.0
100 : $76.45

PE3C8001-36

Pasternack Enterprises

Key Specifications, Connector 1 Series: N, Connector 1 Gender: Male, Connector 1 Polarity: Standard, Connector Angle 1: Straight, Connector 1 Impedance: 50 Ohm, Connector 2 Series: N, Connector 2 Gender: Female, Connector 2 Polarity: Standard, Connector Angle 2: Straight, Connector 2 Impedance: 50 Ohm, Connector 1 Body Material: Brass, Connector 1 Body Plating: Tri-Metal, RF Cable Part Number: TFT-5G-402, RF Cable Type: TFT-5G-402, RF Cable Impedance: 50 Ohm, Length, Max: 36 inches. N Male to N Female Low PIM Cable 36 Inch Length Using TFT-5G-402 Coax Using Times Microwave Components., Radio frequency assembly N male to N female low PIM cable 36 inch length using TFT-5G-402 coax using Times Microwave components from Pasternack is part of one of the largest selections of same-day ship coaxial cables for RF, microwave and millimeter wave interconnect solutions. Pasternack low PIM (Passive Intermodulation, also called Intermod for short) coaxial cable assembly products are used in applications requiring high quality, such as laboratory RF test and measurement, rugged and designed for defense/military, telecom antenna tower component jumper connection, production environments, general use, etc. The N male to N female low PIM cable 36 inch length using TFT-5G-402 coax using Times Microwave components, like our other Pasternack coaxial cable assemblies, will ship the same day, and any custom type N to type N cable assembly orders will ship the same business day as well. Pasternack RF coax low PIM cable assembly is built with a type N cable connection on one end and a type N cable connection on the other. Our low PIM type N to type N cable assembly has a male gender on end 1 and a female on end 2. PE3C8001-36 can also be known as a low PIM type N plug to type N jack cable assembly and will be shipped the same day as it is purchased. This flexible RF cable assembly with a 0.808-inch diameter has copper as the cable's inner conducting material and PTFE dielectric type. type N low PIM cable assemblies from Pasternack are ideal for applications including indoor and outdoor use and plenum rated applications. The minimum bend radius for this cable is 0.75 inches, allowing for a single bend without damaging the cable. Our PE3C8001-36 RF cable has a FEP jacket of 0.160-inch diameter. This radio frequency cable assembly can withstand temperatures ranging from -40 to 125 degrees C. The flexible RF cable has an in-series connection. This cable assembly has a typical propagation velocity of 76% and a minimum RF shielding of 80 dB. Our type N male to type N female cable has a maximum VSWR of 1.4:1. Type N plug to type N jack cable assembly PE3C8001-36 is built with TFT-5G-402 which is a flexible coax type. The Pasternack low passive intermodulation flexible type N cable assembly is manufactured with type N to type N cable connectors, has a 50 Ohm impedance, and is double shielded. Both the connectors have a solder/solder attachment method and a brass body. Additional dimensions, specifications and CAD drawings for this low PIM RF cable are available on our downloadable PDF datasheet. PE3C8001-36 can also be used in the other direction and will be a type N female to type N male cable assembly if the opposite connectivity is required. Low PIM type N plug to type N jack cable assembly is just one of more than one million in-stock RF products available. Pasternack is where to buy a high quality type N to type N cable assembly for quick shipment worldwide. Variations of type N cable assemblies can also be built and will ship on the same day as well, search this website or contact us for assistance. High quality custom RF cable assembly products for microwave and millimeter wave radio transmitter receiver, antenna jumper, component interconnection and more for RF test & measurement labs, rugged and MIL-STD designed military/defense, aerospace, telecom, phase stable, phase and delay matching, outdoor and harsh environment and other radio frequency applications can be manufactured. For further information on similar products, our expert technical support and trained sales team can get you the ideal type N to type N low PIM RF cable assembly as per your requirements.

1 : $86.69
25 : $82.36
50 : $78.02
100 : $74.55

PE3C8001-100CM

Pasternack Enterprises

Key Specifications, Connector 1 Series: N, Connector 1 Gender: Male, Connector 1 Polarity: Standard, Connector Angle 1: Straight, Connector 1 Impedance: 50 Ohm, Connector 2 Series: N, Connector 2 Gender: Female, Connector 2 Polarity: Standard, Connector Angle 2: Straight, Connector 2 Impedance: 50 Ohm, Connector 1 Body Material: Brass, Connector 1 Body Plating: Tri-Metal, RF Cable Part Number: TFT-5G-402, RF Cable Type: TFT-5G-402, RF Cable Impedance: 50 Ohm, Length, Max: 39.37 inches. N Male to N Female Low PIM Cable 100 CM Length Using TFT-5G-402 Coax Using Times Microwave Components., Radio frequency assembly N male to N female low PIM cable 100 cm length using TFT-5G-402 coax using Times Microwave components from Pasternack is part of one of the largest selections of same-day ship coaxial cables for RF, microwave and millimeter wave interconnect solutions. Pasternack low PIM (Passive Intermodulation, also called Intermod for short) coaxial cable assembly products are used in applications requiring high quality, such as laboratory RF test and measurement, rugged and designed for defense/military, telecom antenna tower component jumper connection, production environments, general use, etc. The N male to N female low PIM cable 100 cm length using TFT-5G-402 coax using Times Microwave components, like our other Pasternack coaxial cable assemblies, will ship the same day, and any custom type N to type N cable assembly orders will ship the same business day as well. Pasternack RF coax low PIM cable assembly is built with a type N cable connection on one end and a type N cable connection on the other. Our low PIM type N to type N cable assembly has a male gender on end 1 and a female on end 2. PE3C8001-100CM can also be known as a low PIM type N plug to type N jack cable assembly and will be shipped the same day as it is purchased. This flexible RF cable assembly with a 0.808-inch diameter has copper as the cable's inner conducting material and PTFE dielectric type. type N low PIM cable assemblies from Pasternack are ideal for applications including indoor and outdoor use and plenum rated applications. The minimum bend radius for this cable is 0.75 inches, allowing for a single bend without damaging the cable. Our PE3C8001-100CM RF cable has a FEP jacket of 0.160-inch diameter. This radio frequency cable assembly can withstand temperatures ranging from -40 to 125 degrees C. The flexible RF cable has an in-series connection. This cable assembly has a typical propagation velocity of 76% and a minimum RF shielding of 80 dB. Our type N male to type N female cable has a maximum VSWR of 1.4:1. Type N plug to type N jack cable assembly PE3C8001-100CM is built with TFT-5G-402 which is a flexible coax type. The Pasternack low passive intermodulation flexible type N cable assembly is manufactured with type N to type N cable connectors, has a 50 Ohm impedance, and is double shielded. Both the connectors have a solder/solder attachment method and a brass body. Additional dimensions, specifications and CAD drawings for this low PIM RF cable are available on our downloadable PDF datasheet. PE3C8001-100CM can also be used in the other direction and will be a type N female to type N male cable assembly if the opposite connectivity is required. Low PIM type N plug to type N jack cable assembly is just one of more than one million in-stock RF products available. Pasternack is where to buy a high quality type N to type N cable assembly for quick shipment worldwide. Variations of type N cable assemblies can also be built and will ship on the same day as well, search this website or contact us for assistance. High quality custom RF cable assembly products for microwave and millimeter wave radio transmitter receiver, antenna jumper, component interconnection and more for RF test & measurement labs, rugged and MIL-STD designed military/defense, aerospace, telecom, phase stable, phase and delay matching, outdoor and harsh environment and other radio frequency applications can be manufactured. For further information on similar products, our expert technical support and trained sales team can get you the ideal type N to type N low PIM RF cable assembly as per your requirements.

1 : $82.39
25 : $78.27
50 : $74.15
100 : $70.86

PE3W08001

Pasternack Enterprises

Key Specifications, Connector Series 1: MMCX, Connector Gender 1: Plug, Connector Polarity 1: Standard, Connector Angle 1: Straight, Connector Mount Method 1: None, Connector Impedance 1: 50 Ohm, Connector Series 2: MCX, Connector Gender 2: Plug, Connector Polarity 2: Standard, Connector Angle 2: Right Angle, Connector Mount Method 2: None, Connector Impedance 2: 50 Ohm, RF Cable Part Number: RG178B/U, RF Cable Type: RG178, RF Cable Impedance: 50 Ohm. MMCX Plug to MCX Plug Right Angle Cable Using RG178 Coax. PE3W08001 is a MMCX plug to MCX plug right angle cable using RG178 coax. This Pasternack MMCX plug to MCX plug right angle cable assembly uses a 50 Ohm MMCX for connector 1 and a 50 Ohm MCX for connector 2. MMCX to MCX right angle coaxial cable assembly uses 90 degree right angle coax cable connector. Our plug MMCX to plug MCX right angle cable assembly uses a flexible cable type that is 50 Ohm. Pasternack PE3W08001 MMCX plug to MCX plug right angle cable assembly is constructed with RG178 coax.

PE3W12800-12

Pasternack Enterprises

Key Specifications, Connector 1 Series: 2.2-5, Connector 1 Gender: Male, Connector 1 Polarity: Standard, Connector Angle 1: Straight, Connector 1 Impedance: 50 Ohm, Connector 2 Series: QMA, Connector 2 Gender: Male, Connector 2 Polarity: Standard, Connector Angle 2: Straight, Connector 2 Impedance: 50 Ohm, Connector 1 Body Material: Brass, Connector 1 Body Plating: Silver, RF Cable Part Number: TFT-5G-402, RF Cable Type: TFT-5G-402, RF Cable Impedance: 50 Ohm, Length, Max: 12 inches. 2.2-5 Male to QMA Male Low PIM Cable 12 Inch Length Using TFT-5G-402 Coax With Times Microwave Parts., Radio frequency assembly 2.2-5 male to QMA male low PIM cable 12 inch length using TFT-5G-402 coax with Times Microwave parts from Pasternack is part of one of the largest selections of same-day ship coaxial cables for RF, microwave and millimeter wave interconnect solutions. Pasternack low PIM (Passive Intermodulation, also called Intermod for short) coaxial cable assembly products are used in applications requiring high quality such as laboratory RF test and measurement, rugged and designed for defense / military, telecom antenna tower component jumper connection, production environments, general use, etc. The 2.2-5 male to QMA male low PIM cable 12 inch length using TFT-5G-402 coax with Times Microwave parts, 2.2-5 cable like our other Pasternack coaxial cable assemblies, will ship the same day and any custom 2.2-5 to QMA cable assembly orders will ship same day as well. Pasternack RF coax low PIM cable assembly is built with 2.2-5 cable connection on one end and QMA cable connection on the other. Our low PIM 2.2-5 to QMA cable assemblies have a male gender on end 1 and male on end 2. PE3W12800-12 can also be known as a low PIM 2.2-5 plug to QMA plug cable assembly and will be shipped same-day as it is purchased. 2.2-5 plug to QMA plug cable assembly PE3W12800-12 is built with TFT-5G-402 which is a flexible coax type. The Pasternack low passive intermodulation flexible 2.2-5 cable assembly is manufactured with 2.2-5 to QMA cable connectors, has a 50 Ohm impedance and is double shielded. RF specs on this 3 GHz maximum frequency low PIM 2.2-5 male to QMA male cable are located on the specifications PDF datasheet on this page along with CAD drawing and dimensions. PE3W12800-12 can also be used in the other direction and will be QMA male to 2.2-5 male cable assembly if the opposite connectivity is required. Low PIM 2.2-5 plug to QMA plug cable assembly is just one of more than 45,000 in-stock RF products available. Pasternack is where to buy a high quality 2.2-5 to QMA cable assembly for quick shipment worldwide. Variations of 2.2-5 cable assemblies can also be built and will ship same-day as well, search this website or contact us for assistance. High quality custom RF cable assembly products for microwave and millimeter wave radio transmitter receiver, antenna jumper, component inter-connection and more for RF test & measurement labs, rugged and MIL-STD designed military / defense, aerospace, telecom, phase stable, phase and delay matching, outdoor and harsh environment and other radio frequency applications can be manufactured. For all these reasons and more, Pasternack is one of the best websites where to find and buy quality RF cable assemblies like this 2.2-5 male to QMA male low PIM cable 12 inch length using TFT-5G-402 coax with Times Microwave parts.

1 : $93.09
25 : $88.44
50 : $83.78
100 : $80.06

PE3800-12

Pasternack Enterprises

Key Specifications, Connector Series 1: SMA, Connector Gender 1: Male, Connector Polarity 1: Standard, Connector Angle 1: Right Angle, Connector Mount Method 1: None, Connector Impedance 1: 50 Ohm, Connector Series 2: SMA, Connector Gender 2: Female, Connector Polarity 2: Standard, Connector Angle 2: Straight, Connector Mount Method 2: Bulkhead, Connector Impedance 2: 50 Ohm, RF Cable Part Number: RG223/U, RF Cable Type: RG223, RF Cable Impedance: 50 Ohm, Length: 12 inches. SMA Male Right Angle to SMA Female Bulkhead Cable 12 Inch Length Using RG223 Coax., Radio frequency assembly SMA male right angle to SMA female bulkhead cable 12 inch length using RG223 coax from Pasternack is part of the largest selections of same-day ship coaxial cables for RF, microwave and millimeter wave interconnect solutions. Pasternack coaxial cable assembly products are used in applications requiring high quality such as laboratory RF test and measurement, rugged and designed for defense / military, telecom antenna tower component jumper connection, production environments, general use, etc. SMA male right angle to SMA female bulkhead cable 12 inch length using RG223 coax, like our other Pasternack coaxial cable assemblies, will ship the same day and any custom SMA to SMA cable assembly orders will ship same day as well. Pasternack RF coax cable assembly is built with right angle SMA cable connection on one end and SMA bulkhead cable connection on the other. Our right angle SMA to SMA cable assemblies have a male gender on end 1 and female on end 2. This SMA to SMA cable is a male to female coax assembly, PE3800-12, can also be known as a right angle SMA plug to SMA jack cable assembly and will be shipped same-day as it is purchased. SMA plug to SMA jack cable assembly PE3800-12 is built with RG223 which is a flexible coax type. The Pasternack flexible SMA cable assembly is manufactured with right angle SMA to SMA cable connectors, has a 50 Ohm impedance and is double shielded. RF specs on this 12.4 GHz maximum frequency SMA right angle male to SMA female bulkhead cable are located on the specifications PDF datasheet on this page along with CAD drawing and dimensions. PE3800-12 can also be used in the other direction and will be SMA female bulkhead to right angle SMA male cable assembly if the opposite connectivity is required. SMA right angle plug to SMA jack bulkhead cable assembly is just one of more than 45,000 in-stock RF products available. Pasternack is where to buy a high quality SMA to SMA cable assembly for quick shipment worldwide. Variations of SMA cable assemblies can also be built and will ship same-day as well, search this website or contact us for assistance. High quality custom RF cable assembly products for microwave and millimeter wave radio transmitter receiver, antenna jumper, component inter-connection and more for RF test & measurement labs, rugged and MIL-STD designed military / defense, aerospace, telecom, phase stable, phase and delay matching, outdoor and harsh environment and other radio frequency applications can be manufactured. For all these reasons and more, Pasternack is one of the best websites where to find and buy quality RF cable assemblies like this SMA male right angle to SMA female bulkhead cable 12 inch length using RG223 coax.

1 : $94.19
25 : $89.48
50 : $84.77
100 : $81.0

PE3C8001-200CM

Pasternack Enterprises

Key Specifications, Connector 1 Series: N, Connector 1 Gender: Male, Connector 1 Polarity: Standard, Connector Angle 1: Straight, Connector 1 Impedance: 50 Ohm, Connector 2 Series: N, Connector 2 Gender: Female, Connector 2 Polarity: Standard, Connector Angle 2: Straight, Connector 2 Impedance: 50 Ohm, Connector 1 Body Material: Brass, Connector 1 Body Plating: Tri-Metal, RF Cable Part Number: TFT-5G-402, RF Cable Type: TFT-5G-402, RF Cable Impedance: 50 Ohm, Length, Max: 78.74 inches. N Male to N Female Low PIM Cable 200 CM Length Using TFT-5G-402 Coax Using Times Microwave Components., Radio frequency assembly N male to N female low PIM cable 200 cm length using TFT-5G-402 coax using Times Microwave components from Pasternack is part of one of the largest selections of same-day ship coaxial cables for RF, microwave and millimeter wave interconnect solutions. Pasternack low PIM (Passive Intermodulation, also called Intermod for short) coaxial cable assembly products are used in applications requiring high quality, such as laboratory RF test and measurement, rugged and designed for defense/military, telecom antenna tower component jumper connection, production environments, general use, etc. The N male to N female low PIM cable 200 cm length using TFT-5G-402 coax using Times Microwave components, like our other Pasternack coaxial cable assemblies, will ship the same day, and any custom type N to type N cable assembly orders will ship the same business day as well. Pasternack RF coax low PIM cable assembly is built with a type N cable connection on one end and a type N cable connection on the other. Our low PIM type N to type N cable assembly has a male gender on end 1 and a female on end 2. PE3C8001-200CM can also be known as a low PIM type N plug to type N jack cable assembly and will be shipped the same day as it is purchased. This flexible RF cable assembly with a 0.808-inch diameter has copper as the cable's inner conducting material and PTFE dielectric type. type N low PIM cable assemblies from Pasternack are ideal for applications including indoor and outdoor use and plenum rated applications. The minimum bend radius for this cable is 0.75 inches, allowing for a single bend without damaging the cable. Our PE3C8001-200CM RF cable has a FEP jacket of 0.160-inch diameter. This radio frequency cable assembly can withstand temperatures ranging from -40 to 125 degrees C. The flexible RF cable has an in-series connection. This cable assembly has a typical propagation velocity of 76% and a minimum RF shielding of 80 dB. Our type N male to type N female cable has a maximum VSWR of 1.4:1. Type N plug to type N jack cable assembly PE3C8001-200CM is built with TFT-5G-402 which is a flexible coax type. The Pasternack low passive intermodulation flexible type N cable assembly is manufactured with type N to type N cable connectors, has a 50 Ohm impedance, and is double shielded. Both the connectors have a solder/solder attachment method and a brass body. Additional dimensions, specifications and CAD drawings for this low PIM RF cable are available on our downloadable PDF datasheet. PE3C8001-200CM can also be used in the other direction and will be a type N female to type N male cable assembly if the opposite connectivity is required. Low PIM type N plug to type N jack cable assembly is just one of more than one million in-stock RF products available. Pasternack is where to buy a high quality type N to type N cable assembly for quick shipment worldwide. Variations of type N cable assemblies can also be built and will ship on the same day as well, search this website or contact us for assistance. High quality custom RF cable assembly products for microwave and millimeter wave radio transmitter receiver, antenna jumper, component interconnection and more for RF test & measurement labs, rugged and MIL-STD designed military/defense, aerospace, telecom, phase stable, phase and delay matching, outdoor and harsh environment and other radio frequency applications can be manufactured. For further information on similar products, our expert technical support and trained sales team can get you the ideal type N to type N low PIM RF cable assembly as per your requirements.

1 : $93.09
25 : $88.44
50 : $83.78
100 : $80.06

PE3C8001-12

Pasternack Enterprises

Key Specifications, Connector 1 Series: N, Connector 1 Gender: Male, Connector 1 Polarity: Standard, Connector Angle 1: Straight, Connector 1 Impedance: 50 Ohm, Connector 2 Series: N, Connector 2 Gender: Female, Connector 2 Polarity: Standard, Connector Angle 2: Straight, Connector 2 Impedance: 50 Ohm, Connector 1 Body Material: Brass, Connector 1 Body Plating: Tri-Metal, RF Cable Part Number: TFT-5G-402, RF Cable Type: TFT-5G-402, RF Cable Impedance: 50 Ohm, Length, Max: 12 inches. N Male to N Female Low PIM Cable 12 Inch Length Using TFT-5G-402 Coax Using Times Microwave Components., Radio frequency assembly N male to N female low PIM cable 12 inch length using TFT-5G-402 coax using Times Microwave components from Pasternack is part of one of the largest selections of same-day ship coaxial cables for RF, microwave and millimeter wave interconnect solutions. Pasternack low PIM (Passive Intermodulation, also called Intermod for short) coaxial cable assembly products are used in applications requiring high quality, such as laboratory RF test and measurement, rugged and designed for defense/military, telecom antenna tower component jumper connection, production environments, general use, etc. The N male to N female low PIM cable 12 inch length using TFT-5G-402 coax using Times Microwave components, like our other Pasternack coaxial cable assemblies, will ship the same day, and any custom type N to type N cable assembly orders will ship the same business day as well. Pasternack RF coax low PIM cable assembly is built with a type N cable connection on one end and a type N cable connection on the other. Our low PIM type N to type N cable assembly has a male gender on end 1 and a female on end 2. PE3C8001-12 can also be known as a low PIM type N plug to type N jack cable assembly and will be shipped the same day as it is purchased. This flexible RF cable assembly with a 0.808-inch diameter has copper as the cable's inner conducting material and PTFE dielectric type. type N low PIM cable assemblies from Pasternack are ideal for applications including indoor and outdoor use and plenum rated applications. The minimum bend radius for this cable is 0.75 inches, allowing for a single bend without damaging the cable. Our PE3C8001-12 RF cable has a FEP jacket of 0.160-inch diameter. This radio frequency cable assembly can withstand temperatures ranging from -40 to 125 degrees C. The flexible RF cable has an in-series connection. This cable assembly has a typical propagation velocity of 76% and a minimum RF shielding of 80 dB. Our type N male to type N female cable has a maximum VSWR of 1.4:1. Type N plug to type N jack cable assembly PE3C8001-12 is built with TFT-5G-402 which is a flexible coax type. The Pasternack low passive intermodulation flexible type N cable assembly is manufactured with type N to type N cable connectors, has a 50 Ohm impedance, and is double shielded. Both the connectors have a solder/solder attachment method and a brass body. Additional dimensions, specifications and CAD drawings for this low PIM RF cable are available on our downloadable PDF datasheet. PE3C8001-12 can also be used in the other direction and will be a type N female to type N male cable assembly if the opposite connectivity is required. Low PIM type N plug to type N jack cable assembly is just one of more than one million in-stock RF products available. Pasternack is where to buy a high quality type N to type N cable assembly for quick shipment worldwide. Variations of type N cable assemblies can also be built and will ship on the same day as well, search this website or contact us for assistance. High quality custom RF cable assembly products for microwave and millimeter wave radio transmitter receiver, antenna jumper, component interconnection and more for RF test & measurement labs, rugged and MIL-STD designed military/defense, aerospace, telecom, phase stable, phase and delay matching, outdoor and harsh environment and other radio frequency applications can be manufactured. For further information on similar products, our expert technical support and trained sales team can get you the ideal type N to type N low PIM RF cable assembly as per your requirements.

1 : $67.49
25 : $64.12
50 : $60.74
100 : $58.04

PE88D8001

Pasternack Enterprises

1 : $1,310.0
5 : $1,257.6
10 : $1,205.2
25 : $1,152.8

PE3C8001-150CM

Pasternack Enterprises

Key Specifications, Connector 1 Series: N, Connector 1 Gender: Male, Connector 1 Polarity: Standard, Connector Angle 1: Straight, Connector 1 Impedance: 50 Ohm, Connector 2 Series: N, Connector 2 Gender: Female, Connector 2 Polarity: Standard, Connector Angle 2: Straight, Connector 2 Impedance: 50 Ohm, Connector 1 Body Material: Brass, Connector 1 Body Plating: Tri-Metal, RF Cable Part Number: TFT-5G-402, RF Cable Type: TFT-5G-402, RF Cable Impedance: 50 Ohm, Length, Max: 59.06 inches. N Male to N Female Low PIM Cable 150 CM Length Using TFT-5G-402 Coax Using Times Microwave Components., Radio frequency assembly N male to N female low PIM cable 150 cm length using TFT-5G-402 coax using Times Microwave components from Pasternack is part of one of the largest selections of same-day ship coaxial cables for RF, microwave and millimeter wave interconnect solutions. Pasternack low PIM (Passive Intermodulation, also called Intermod for short) coaxial cable assembly products are used in applications requiring high quality, such as laboratory RF test and measurement, rugged and designed for defense/military, telecom antenna tower component jumper connection, production environments, general use, etc. The N male to N female low PIM cable 150 cm length using TFT-5G-402 coax using Times Microwave components, like our other Pasternack coaxial cable assemblies, will ship the same day, and any custom type N to type N cable assembly orders will ship the same business day as well. Pasternack RF coax low PIM cable assembly is built with a type N cable connection on one end and a type N cable connection on the other. Our low PIM type N to type N cable assembly has a male gender on end 1 and a female on end 2. PE3C8001-150CM can also be known as a low PIM type N plug to type N jack cable assembly and will be shipped the same day as it is purchased. This flexible RF cable assembly with a 0.808-inch diameter has copper as the cable's inner conducting material and PTFE dielectric type. type N low PIM cable assemblies from Pasternack are ideal for applications including indoor and outdoor use and plenum rated applications. The minimum bend radius for this cable is 0.75 inches, allowing for a single bend without damaging the cable. Our PE3C8001-150CM RF cable has a FEP jacket of 0.160-inch diameter. This radio frequency cable assembly can withstand temperatures ranging from -40 to 125 degrees C. The flexible RF cable has an in-series connection. This cable assembly has a typical propagation velocity of 76% and a minimum RF shielding of 80 dB. Our type N male to type N female cable has a maximum VSWR of 1.4:1. Type N plug to type N jack cable assembly PE3C8001-150CM is built with TFT-5G-402 which is a flexible coax type. The Pasternack low passive intermodulation flexible type N cable assembly is manufactured with type N to type N cable connectors, has a 50 Ohm impedance, and is double shielded. Both the connectors have a solder/solder attachment method and a brass body. Additional dimensions, specifications and CAD drawings for this low PIM RF cable are available on our downloadable PDF datasheet. PE3C8001-150CM can also be used in the other direction and will be a type N female to type N male cable assembly if the opposite connectivity is required. Low PIM type N plug to type N jack cable assembly is just one of more than one million in-stock RF products available. Pasternack is where to buy a high quality type N to type N cable assembly for quick shipment worldwide. Variations of type N cable assemblies can also be built and will ship on the same day as well, search this website or contact us for assistance. High quality custom RF cable assembly products for microwave and millimeter wave radio transmitter receiver, antenna jumper, component interconnection and more for RF test & measurement labs, rugged and MIL-STD designed military/defense, aerospace, telecom, phase stable, phase and delay matching, outdoor and harsh environment and other radio frequency applications can be manufactured. For further information on similar products, our expert technical support and trained sales team can get you the ideal type N to type N low PIM RF cable assembly as per your requirements.

1 : $88.89
25 : $84.45
50 : $80.0
100 : $76.45

PE3C8001-24

Pasternack Enterprises

Key Specifications, Connector 1 Series: N, Connector 1 Gender: Male, Connector 1 Polarity: Standard, Connector Angle 1: Straight, Connector 1 Impedance: 50 Ohm, Connector 2 Series: N, Connector 2 Gender: Female, Connector 2 Polarity: Standard, Connector Angle 2: Straight, Connector 2 Impedance: 50 Ohm, Connector 1 Body Material: Brass, Connector 1 Body Plating: Tri-Metal, RF Cable Part Number: TFT-5G-402, RF Cable Type: TFT-5G-402, RF Cable Impedance: 50 Ohm, Length, Max: 24 inches. N Male to N Female Low PIM Cable 24 Inch Length Using TFT-5G-402 Coax Using Times Microwave Components., Radio frequency assembly N male to N female low PIM cable 24 inch length using TFT-5G-402 coax using Times Microwave components from Pasternack is part of one of the largest selections of same-day ship coaxial cables for RF, microwave and millimeter wave interconnect solutions. Pasternack low PIM (Passive Intermodulation, also called Intermod for short) coaxial cable assembly products are used in applications requiring high quality, such as laboratory RF test and measurement, rugged and designed for defense/military, telecom antenna tower component jumper connection, production environments, general use, etc. The N male to N female low PIM cable 24 inch length using TFT-5G-402 coax using Times Microwave components, like our other Pasternack coaxial cable assemblies, will ship the same day, and any custom type N to type N cable assembly orders will ship the same business day as well. Pasternack RF coax low PIM cable assembly is built with a type N cable connection on one end and a type N cable connection on the other. Our low PIM type N to type N cable assembly has a male gender on end 1 and a female on end 2. PE3C8001-24 can also be known as a low PIM type N plug to type N jack cable assembly and will be shipped the same day as it is purchased. This flexible RF cable assembly with a 0.808-inch diameter has copper as the cable's inner conducting material and PTFE dielectric type. type N low PIM cable assemblies from Pasternack are ideal for applications including indoor and outdoor use and plenum rated applications. The minimum bend radius for this cable is 0.75 inches, allowing for a single bend without damaging the cable. Our PE3C8001-24 RF cable has a FEP jacket of 0.160-inch diameter. This radio frequency cable assembly can withstand temperatures ranging from -40 to 125 degrees C. The flexible RF cable has an in-series connection. This cable assembly has a typical propagation velocity of 76% and a minimum RF shielding of 80 dB. Our type N male to type N female cable has a maximum VSWR of 1.4:1. Type N plug to type N jack cable assembly PE3C8001-24 is built with TFT-5G-402 which is a flexible coax type. The Pasternack low passive intermodulation flexible type N cable assembly is manufactured with type N to type N cable connectors, has a 50 Ohm impedance, and is double shielded. Both the connectors have a solder/solder attachment method and a brass body. Additional dimensions, specifications and CAD drawings for this low PIM RF cable are available on our downloadable PDF datasheet. PE3C8001-24 can also be used in the other direction and will be a type N female to type N male cable assembly if the opposite connectivity is required. Low PIM type N plug to type N jack cable assembly is just one of more than one million in-stock RF products available. Pasternack is where to buy a high quality type N to type N cable assembly for quick shipment worldwide. Variations of type N cable assemblies can also be built and will ship on the same day as well, search this website or contact us for assistance. High quality custom RF cable assembly products for microwave and millimeter wave radio transmitter receiver, antenna jumper, component interconnection and more for RF test & measurement labs, rugged and MIL-STD designed military/defense, aerospace, telecom, phase stable, phase and delay matching, outdoor and harsh environment and other radio frequency applications can be manufactured. For further information on similar products, our expert technical support and trained sales team can get you the ideal type N to type N low PIM RF cable assembly as per your requirements.

1 : $80.29
25 : $76.28
50 : $72.26
100 : $69.05

Teledyne HiRel

5962-9758001QEA

Teledyne HiRel

FLIP-FLOP, JK, DUAL
RoHS : Not Compliant

8001901DA

Teledyne HiRel

AND GATE, QUAD 2-INPUT, WITH OPEN-COLLECTOR OUTPUTS
RoHS : Not Compliant

5962-9758001Q2A

Teledyne HiRel

FLIP-FLOP, JK, DUAL
RoHS : Not Compliant

5962-9218001MRA

Teledyne HiRel

LATCH, D-TYPE, 8-BIT, WITH 3-STATE OUTPUTS
RoHS : Not Compliant

5962-9758001QFA

Teledyne HiRel

FLIP-FLOP, JK, DUAL
RoHS : Not Compliant

5962-9218001MSA

Teledyne HiRel

LATCH, D-TYPE, 8-BIT, WITH 3-STATE OUTPUTS
RoHS : Not Compliant

80019012A

Teledyne HiRel

AND GATE, QUAD 2-INPUT, WITH OPEN-COLLECTOR OUTPUTS
RoHS : Not Compliant

8001901CA

Teledyne HiRel

AND GATE, QUAD 2-INPUT, WITH OPEN-COLLECTOR OUTPUTS
RoHS : Not Compliant

80019012C

Teledyne HiRel

AND GATE, QUAD 2-INPUT, WITH OPEN-COLLECTOR OUTPUTS

5962-9218001M2A

Teledyne HiRel

LATCH, D-TYPE, 8-BIT, WITH 3-STATE OUTPUTS
RoHS : Not Compliant

Venkel Ltd.

UPTF1206-8W-P-8001BT

VENKEL LTD

Ultra Precision Thin Film CR;1206;1/8W;5PPM;8K;�0.1%
RoHS : Compliant

Vyrian

M27C800-100XK1TR

STMicroelectronics

RoHS : Compliant

9,050

M27V800-100M1

STMicroelectronics

RoHS : Not Compliant

1,100

43588-0018

Molex

Rectangular Power Connector, 4 Contact(s), Male, Solder Terminal
RoHS : Compliant

1,100

M27V800-120XK1TR

STMicroelectronics

RoHS : Not Compliant

1,050

2800188

Phoenix Contact

Surge Arrestors
RoHS : Compliant

1,050

M27V800-100K1TR

STMicroelectronics

RoHS : Not Compliant

960

M27V800-120K6

STMicroelectronics

RoHS : Not Compliant

830

M27V800-150XB1

STMicroelectronics

RoHS : Not Compliant

820

M27V800-110B1

STMicroelectronics

RoHS : Not Compliant

780

2800189

Phoenix Contact

Surge Arrestors
RoHS : Compliant

340

180-015-203L011

Norcomp Interconnect Devices

330

5962-8778001CA

Texas Instruments

Instrumentation Amplifier, 1 Func, 75uV Offset-Max, CDIP14

290

M38510/38001SFA

Texas Instruments

Binary Counter, ALS Series, Synchronous, Positive Edge Triggered, 4-Bit, Up Direction, TTL, CDFP16

100

5962-9558001QJX

Texas Instruments

Multiplexer, TTL/H/L Series, 1-Func, 16 Line Input, 1 Line Output, Inverted Output, TTL, CDIP24

5DF-800102000123057

Intel Corporation

Waytek, Inc.

19038-0013

Molex

16-14 GA .180 Female Bullet Connector Blue Nylon Insulation
RoHS : Compliant

50 : $0.2059
200 : $0.1871
500 : $0.1812
1,000 : $0.1737
5,000 : $0.1658

39,250

931680017

HELLA KGaA Hueck & Co

Mini Relay 20/40 AMP SPDT 12V CONNECTOR 75280 75281 OR 75282

1 : $6.52
50 : $5.47
100 : $5.15
200 : $4.85
500 : $4.63

1,463

880014

Cole Hersee

MEGA AMG Sealed SN Fuse Block 500A 60V DC SAE J1171 ISO 8846 LIKE BLUE SEA 7721 78162

1 : $52.02
5 : $46.9
10 : $44.08
50 : $41.77
100 : $39.97
200 : $38.18

1,131

506-11318-001

Carling Technologies

Carling Technologies 506-11318-001 Contura switch body boot is a protective boot for Carling Contura rocker switch bodies. Designed for use with the switch body sold separately, it helps complete modular Contura switch assemblies where added switch body protection is required.

1 : $7.02
50 : $5.86
100 : $5.1
200 : $4.78
500 : $4.59

283

H84708001

HELLA KGaA Hueck & Co

The Hella H84708801 is a Mini ISO / ISO 280 weatherproof relay connector designed for secure connections in harsh automotive and mobile electrical systems. Featuring a 5-pin configuration with pre-wired 12" leads, it supports high-current relay circuits and simplifies installation. Built with sealed construction and durable wiring , it provides reliable, moisture-resistant performance for lighting, motors, and auxiliary equipment.

1 : $25.48
5 : $22.76
10 : $21.3
50 : $20.05
100 : $19.11
200 : $18.28

142

624 1668 0 01

Rennsteig Tools Inc

FCI,Apex 2.8 Crimp Die Locator 20-14GA Male Terminals

1 : $110.49
10 : $104.16

Win Source Electronics

TPS7A8001DRBT

Texas Instruments

Low-Noise, High-Bandwidth PSRR, Low-Dropout 1A Linear Regulator
RoHS : Compliant

1,075 : $0.2796
860 : $0.291
665 : $0.3023
465 : $0.325
300 : $0.3364
140 : $0.3591

214,330

TPS78001DRVRG4

Texas Instruments

IC REG LIN POS ADJ 150MA 6WSON
RoHS : Compliant

820 : $0.4113
655 : $0.428
505 : $0.4448
355 : $0.4781
230 : $0.4948
110 : $0.5283

108,800

0438001.WR

Littelfuse Inc

FUSE BRD MNT 1A 32VAC 63VDC 0603
RoHS : Compliant

3,840 : $0.0782
2,865 : $0.0873
2,215 : $0.0903
1,610 : $0.0933
1,040 : $0.0963
430 : $0.1173

59,090

JN5168/001

Nexperia

74 : $4.1031
55 : $4.5765
43 : $4.7343
31 : $4.8922
20 : $5.05
9 : $6.1546

30,000

AD8001ART-REEL7

Analog Devices Inc

IC OPAMP CFA 795MHZ SOT23-5
RoHS : Not Compliant

102 : $2.9546
76 : $3.2955
59 : $3.4091
43 : $3.5227
28 : $3.6364
12 : $4.4318

20,000

AD8001ART

Analog Devices Inc

Op Amp 880MHz 5-Lead SOT-23

101 : $2.9771
76 : $3.3207
59 : $3.4352
43 : $3.5497
28 : $3.6642
12 : $4.4657

20,000

0458001.DR

Littelfuse Inc

Surface Mount Fuses
RoHS : Compliant

835 : $0.3598
625 : $0.4013
485 : $0.4151
350 : $0.429
230 : $0.4428
95 : $0.5397

15,000

TPS78001DD

Texas Instruments

LDO Voltage Regulator Adj 150mA TSOT-23-6

760 : $0.397
565 : $0.4428
440 : $0.4581
320 : $0.4733
205 : $0.4886
85 : $0.5955

6,000

TPS78001DDCRG4

Texas Instruments

IC REG LIN POS ADJ 150MA SOT23-5
RoHS : Compliant

675 : $0.4473
540 : $0.4655
415 : $0.4837
290 : $0.52
190 : $0.5382
90 : $0.5746

5,590

0448001.MR

Littelfuse Inc

Surface Mount Fuses Surface Mount Fuses
RoHS : Compliant

915 : $0.3287
735 : $0.342
565 : $0.3554
395 : $0.3821
255 : $0.3955
120 : $0.4222

4,000

KSZ8001LI-TR

Microchip Technology Inc

IC TXRX PHY 10/100 3.3V 48LQFP
RoHS : Compliant

39 : $7.8596
29 : $8.7665
23 : $9.0688
17 : $9.371
11 : $9.6733
5 : $11.7894

1,855

AD8001ARTZ

Analog Devices Inc

IC OPAMP CFA 795MHZ SOT23-5
RoHS : Compliant

78 : $4.3463
58 : $4.8478
45 : $5.015
33 : $5.1821
21 : $5.3493
9 : $6.5194

659

AD8001ARTZ-REEL7

Analog Devices Inc

IC OPAMP CFA 795MHZ SOT23-5
RoHS : Compliant

78 : $4.3463
58 : $4.8478
45 : $5.015
33 : $5.1821
21 : $5.3493
9 : $6.5194

620

CY7C68001-56PVXC

Cypress Semiconductor

Full Speed/High Speed USB Interface Device USB 2.0 3.3V Tube 56-Pin SSOP / IC USB INTERFACE SX2 56-SSOP
RoHS : Compliant

1 : $732.3665

512

AD8001AR-REEL7

Analog Devices Inc

IC OPAMP CFA 715MHZ 8SOIC
RoHS : Not Compliant

40 : $8.4588
32 : $8.8112
25 : $9.1636
18 : $9.8685
11 : $10.221
6 : $10.9258

320

8001L-R20-R Distributor

Link URL