M30620FCAFP datasheet(270/274 Pages) MITSUBISHI

270 / 274 page

Contents for change

Revision

date

Version

Revision history

M16C/62A Group data sheet

Mitsubishi microcomputers

M16C / 62A Group

SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER

270

Revision History

REV.A1

99.12.21

Page 145 Note 2

• Before data can be written to the SI/Oi transmit/receive register (addresses

036016, 036416), the CLKi pin input must be in the low state. Also, before rewriting

the SI/Oi Control Register (addresses 036216, 036616)’s bit 7 (SOUTi initial value

set bit), make sure the CLKi pin input is held low. ---> • Before data can be written

to the SI/Oi transmit/receive register (addresses 036016, 036416), the CLKi pin

input must be in the high state. Also, before rewriting the SI/Oi Control Register

(addresses 036216, 036616)’s bit 7 (SOUTi initial value set bit), make sure the CLKi

pin input is held high.

00.7.3

REV. A2

Page 43, Figure 1.10.6

Note: Writing a value to an address after “1” is written to this bit returns the bit to

“0” . Other bits do not automatically return to “0” and they must therefore

be reset by the program.

Page 144, Figure 1.16.32, bit 5 of the SI/Oi control register (i=3, 4)

Transfer direction lect bit --->Transfer direction select bit

Page 144, Figure 1.16.32, Note 2

When using the port as an input/output port by setting the SI/Oi port select bit (i =

3, 4) to “1”, be sure to set the sync clock select bit to “1”.

--->

When using the port as an input/output port by setting the SI/Oi port select bit (i =

3, 4) to “0”, be sure to set the sync clock select bit to “1”.

00.7.10

Page 115, 139, Bit 3 of the UART2 special mode register 2 (bit symbol)

ASL --> ALS

01.3.27

REV. B

Page 2 Note is added in Figure 1.1.1.

Page 3 Note is added in Figure 1.1.2.

Page 10 Explanation of “Memory” is partly revised.

Page 10 Figure 1.3.1 is partly revised.

Page 22 Figure 1.7.1 is partly revised.

Page 23 Figure 1.7.2 is partly revised.

Page 23 “Internal Reserved Area Expansion Bit (PM13)” is added.

Page 24 Figure 1.7.3 is partly revised.

Page 25 Explanation of “(3) Selecting separate/multiplex bus” is partly revised.

Page 28 Explanation of “(2) Chip select signal” is partly added.

Page 29 Figure 1.9.2 is added.

Page 37 Explanation of “(2) Sub-clock” is partly revised.

Page 38 Figure 1.10.4 is partly revised.

Page 39 Explanation of “Stop Mode” is partly revised.

Page 39 Table 1.10.2 is partly revised.

Page 40 Explanation of “Wait Mode” is partly revised.

Page 40 Table 1.10.3 is partly revised.

Page 42 Explanation of “Power Control” is partly revised.

Page 62 Explanation of “Address Match Interruptl” is partly revised.

M30620FCAFP Datasheet(PDF) 270 Page - Mitsubishi Electric Semiconductor

M30620FCAFP Datasheet(HTML) 270 Page - Mitsubishi Electric Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL