Electronic Components Datasheet Search
  English  ▼
ALLDATASHEET.COM

X  

LMC7211 Datasheet(PDF) 8 Page - National Semiconductor (TI)

[Old version datasheet] Texas Instruments acquired National semiconductor.
Part # LMC7211
Description  Tiny CMOS Comparator with Rail-to-Rail Input and Push-Pull Output
Download  13 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  NSC [National Semiconductor (TI)]
Direct Link  http://www.national.com
Logo NSC - National Semiconductor (TI)

LMC7211 Datasheet(HTML) 8 Page - National Semiconductor (TI)

Back Button LMC7211 Datasheet HTML 4Page - National Semiconductor (TI) LMC7211 Datasheet HTML 5Page - National Semiconductor (TI) LMC7211 Datasheet HTML 6Page - National Semiconductor (TI) LMC7211 Datasheet HTML 7Page - National Semiconductor (TI) LMC7211 Datasheet HTML 8Page - National Semiconductor (TI) LMC7211 Datasheet HTML 9Page - National Semiconductor (TI) LMC7211 Datasheet HTML 10Page - National Semiconductor (TI) LMC7211 Datasheet HTML 11Page - National Semiconductor (TI) LMC7211 Datasheet HTML 12Page - National Semiconductor (TI) Next Button
Zoom Inzoom in Zoom Outzoom out
 8 / 13 page
background image
Application Information (Continued)
From
Figure 3, the shoot-through current for the LMC7211
can be calculated to be 0.2 mA (typical), and the duration is
1 µs. The values needed for the bypass capacitors can be
calculated as follows:
Area of
∆ = 12 (1 µs x 200 µA)
= 100 pC
The capacitor needs to supply 100 picocolumb. To avoid
large shifts in the comparator threshold due to changes in
the voltage level, the voltage drop at the bypass capacitor
should be limited to 100 mV or less.
The charge needed (100 picocolumb) and the allowable volt-
age drop (100 mV) will give us the minimum capacitor value
required.
∆Q = C(∆V)
C =
∆Q/∆V = 100 picocolumb/100 mV
C = 10-10/10
-1 = 10-9 = 1nF = 0.001 µF
10
-9 = 1nF = 0.001 µF
The voltage drop of
∼100 mV will cause a threshold shift in
the comparator. This threshold shift will be reduced by the
power supply rejection ratio, (PSRR). The PSRR which is
applicable here is not the DC value of PSRR (
∼80 dB), but a
transient PSRR which will be usually about 20 dB–40 dB,
depending on the circuit and the speed of the transient. This
will result in an effective threshold shift of about 1 mV to
10 mV.
For precision and level sensing circuits, it is generally a good
goal to reduce the voltage delta on the power supply to a
value equal to or less than the hysteresis of the comparator
circuit. If the above circuit was to be used with 50 mV of hys-
teresis, it would be reasonable to increase the bypass ca-
pacitor to 0.01 µF to reduce the voltage delta to 10 mV.
Larger values may be useful for obtaining more accurate and
consistent switching.
Note that the switching current of the comparator can spread
to other parts of the board as noise. The bypass capacitor re-
duces this noise. For low noise systems this may be reason
to make the capacitor larger.
For non-precision circuits, such as using a comparator to de-
termine if a push-button switch is on or off, it is often cheaper
and easier to use a larger value of hysteresis and a small
value or bypass capacitance. The low shoot-through current
of the LMC7211 can allow the use of smaller and less expen-
sive bypass capacitors in non-critical circuits.
4.0 Output Short Circuit Current
The LMC7211 has short circuit protection of 40 mA. How-
ever, it is not designed to withstand continuous short circuits,
transient voltage or current spikes, or shorts to any voltage
beyond the supplies. A resistor in series with the output
should reduce the effect of shorts. For outputs which send
signals off PC boards additional protection devices, such as
diodes to the supply rails, and varistors may be used.
5.0 Hysteresis
If the input signal is very slow or very noisy, the comparator
output might trip several times as the input signal passes
through the threshold. Using positive feedback to add hys-
teresis to the switching can reduce or eliminate this problem.
The positive feedback can be added by a high value resistor
(R
F). This will result in two switching thresholds, one for in-
creasing signals and one for decreasing signals. A capacitor
can be added across R
F to increase the switching speed and
provide more short term hysteresis. This can result in greater
noise immunity for the circuit.
See
Figure 4, Figure 5 and Figure 6.
Note that very heavy loading of the comparator output, such
as LED drive or bipolar logic gates, will change the output
voltage and shift the voltage thresholds.
DS012337-6
FIGURE 2. Circuit for Measurement of the
Shoot-Through Current
DS012337-7
FIGURE 3. Measurement of the Shoot-Through Current
DS012337-8
www.national.com
8


Similar Part No. - LMC7211

ManufacturerPart #DatasheetDescription
logo
Texas Instruments
LMC7211 TI1-LMC7211 Datasheet
431Kb / 18P
[Old version datasheet]   Tiny CMOS Comparator with Rail-to-Rail Input and Push-Pull Output
LMC7211-N TI-LMC7211-N Datasheet
1Mb / 22P
[Old version datasheet]   LMC7211 Tiny CMOS Comparator with Rail-to-Rail Input and Push-Pull Output
LMC7211-N TI1-LMC7211-N Datasheet
1Mb / 23P
[Old version datasheet]   LMC7211 Tiny CMOS Comparator with Rail-to-Rail Input and Push-Pull Output
LMC7211-N TI1-LMC7211-N Datasheet
1Mb / 22P
[Old version datasheet]   LMC7211 Tiny CMOS Comparator with Rail-to-Rail Input and Push-Pull Output
LMC7211-N TI1-LMC7211-N_14 Datasheet
1Mb / 23P
[Old version datasheet]   LMC7211 Tiny CMOS Comparator with Rail-to-Rail Input and Push-Pull Output
More results

Similar Description - LMC7211

ManufacturerPart #DatasheetDescription
logo
Texas Instruments
LMC7211 TI1-LMC7211 Datasheet
431Kb / 18P
[Old version datasheet]   Tiny CMOS Comparator with Rail-to-Rail Input and Push-Pull Output
LMC7211-N TI1-LMC7211-N_14 Datasheet
1Mb / 23P
[Old version datasheet]   LMC7211 Tiny CMOS Comparator with Rail-to-Rail Input and Push-Pull Output
LMC7211-N TI1-LMC7211-N Datasheet
1Mb / 22P
[Old version datasheet]   LMC7211 Tiny CMOS Comparator with Rail-to-Rail Input and Push-Pull Output
LMC7211AIM5X TI-LMC7211AIM5X Datasheet
1Mb / 22P
[Old version datasheet]   LMC7211 Tiny CMOS Comparator with Rail-to-Rail Input and Push-Pull Output
LMC6762 TI1-LMC6762_14 Datasheet
1Mb / 22P
[Old version datasheet]   Dual MicroPower Rail-To-Rail Input CMOS Comparator with Push-Pull Output
logo
National Semiconductor ...
LMC6762 NSC-LMC6762 Datasheet
317Kb / 13P
   Dual MicroPower Rail-To-Rail Input CMOS Comparator with Push-Pull Output
LMC7221 NSC-LMC7221 Datasheet
271Kb / 12P
   Tiny CMOS Comparator with Rail-To-Rail Input and Open Drain Output
LMC7221 NSC-LMC7221_06 Datasheet
699Kb / 13P
   Tiny CMOS Comparator with Rail-To-Rail Input and Open Drain Output
logo
Texas Instruments
TLV7211 TI-TLV7211_10 Datasheet
722Kb / 20P
[Old version datasheet]   CMOS COMPARATORS WITH RAIL-TO-RAIL INPUT AND PUSH-PULL OUTPUT
TLV7211 TI-TLV7211 Datasheet
469Kb / 16P
[Old version datasheet]   CMOS COMPARATORS WITH RAIL-TO-RAIL INPUT AND PUSH-PULL OUTPUT
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13


Datasheet Download

Go To PDF Page


Link URL




Privacy Policy
ALLDATASHEET.COM
Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Datasheet Upload   |   Contact us   |   Privacy Policy   |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com