Electronic Components Datasheet Search
  English  ▼
ALLDATASHEET.COM

X  

409-5626 Datasheet(PDF) 4 Page - TE Connectivity Ltd

Part # 409-5626
Description  AUGAT HOLTITE Sockets
Download  7 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  TEC [TE Connectivity Ltd]
Direct Link  http://www.te.com/usa-en/home.html
Logo TEC - TE Connectivity Ltd

409-5626 Datasheet(HTML) 4 Page - TE Connectivity Ltd

  409-5626 Datasheet HTML 1Page - TE Connectivity Ltd 409-5626 Datasheet HTML 2Page - TE Connectivity Ltd 409-5626 Datasheet HTML 3Page - TE Connectivity Ltd 409-5626 Datasheet HTML 4Page - TE Connectivity Ltd 409-5626 Datasheet HTML 5Page - TE Connectivity Ltd 409-5626 Datasheet HTML 6Page - TE Connectivity Ltd 409-5626 Datasheet HTML 7Page - TE Connectivity Ltd  
Zoom Inzoom in Zoom Outzoom out
 4 / 7 page
background image
114- 13033
Rev B
4
of 7
3.5. Socket Insertion
A. Hole Size Inspection
Using the red NO--GO gage, part number 5--1437514--1, end of the tool provided in the AUGAT HOLTITE
Printed Wiring Contact Kit, check to ensure the hole dimensions are correct. If not, rework may be
necessary or socket selection may need to be re--checked.
B. Insertion
Sockets are inserted into the pc board using a spring loaded hand tool, a pneumatic hand tool system,
flat--rock press--in tooling, or commercially available vibratory/vacuum systems using fully automatic
machines. Two different tips may be used for socket insertion into the pc board. The blue tip is used for
the 5P, 14P, and 27P series sockets. The other insertion tip is white and is used for the 6P, 8P, and 12P
series sockets. Refer to Section 5, TOOLING for specific related tooling part numbers.
3.6. Checking Installed Socket
Once the socket is installed, verification may be made to a correct installation according to the information and
dimensions provided in Figures 2 and 4.
A. Referee Test
Inspection may reveal that some of the hole diameters are at the high limit of the tolerance. If this marginal
condition occurs, a “referee test” should be performed to determine if the holes are suitable for 5P
AUGAT HOLTITE Socket insertion.
Selectively load the sockets into the suspect holes and perform a push--out test using an adequate axial
force gauge (e.g., a hand held CHATILLON Force Gauge). Force should be applied to the socket fingers
only in an axial direction. Socket retention forces will vary with each application due to differences in
socket population density, substrate materials, and number of PC layers. The minimum acceptable
push--out force for all 5P AUGAT HOLTITE Sockets is [4 lbs.] (conforming to MIL--S--83505/6).
B. Insertion Verification
TE suggests verifying that the sockets have been loaded into all of the desired locations. This procedure
could be accomplished visually or with any type of available automatic non--contacting inspection system.
For visual inspection, place a light source under the pc board an examine the holes form above. A small
point of light indicates the socket is present. A large point of light indicates the socket may be missing. The
light pattern may be compared to a chart showing socket locations.
Figure 4
Plated Through
Hole
Finished
Diameter
Hole
Vertical Profile
Dimension (Max)
Socket
Area Dia.
Glass Epoxy Substrate
CHATILLON is a trademark


Similar Part No. - 409-5626

ManufacturerPart #DatasheetDescription
logo
TE Connectivity Ltd
409-5626 TEC-409-5626 Datasheet
338Kb / 14P
   Single Connector Attachments
More results

Similar Description - 409-5626

ManufacturerPart #DatasheetDescription
logo
Tyco Electronics
2-1437514-5 MACOM-2-1437514-5 Datasheet
266Kb / 5P
   AUGAT* HOLTITE* Sockets
2-1437514-9 MACOM-2-1437514-9 Datasheet
266Kb / 5P
   AUGAT* HOLTITE* Sockets
2-1437514-8 MACOM-2-1437514-8 Datasheet
266Kb / 5P
   AUGAT* HOLTITE* Sockets
2-1437514-6 MACOM-2-1437514-6 Datasheet
266Kb / 5P
   AUGAT* HOLTITE* Sockets
2-1437542-7 MACOM-2-1437542-7 Datasheet
586Kb / 3P
   700 SERIES AUGAT DIP SOCKETS, DISPOSABLE CARRIER
2-1437542-9 MACOM-2-1437542-9 Datasheet
586Kb / 3P
   700 SERIES AUGAT DIP SOCKETS, DISPOSABLE CARRIER
2-1437542-2 MACOM-2-1437542-2 Datasheet
586Kb / 3P
   700 SERIES AUGAT DIP SOCKETS, DISPOSABLE CARRIER
2-1437506-4 MACOM-2-1437506-4 Datasheet
182Kb / 1P
   HOLTITE CONTACTS
2-1437506-0 MACOM-2-1437506-0 Datasheet
182Kb / 1P
   HOLTITE CONTACTS
2-1437514-0 MACOM-2-1437514-0 Datasheet
32Kb / 1P
   ASSEMBLY, HOLTITE, REELED
More results


Html Pages

1 2 3 4 5 6 7


Datasheet Download

Go To PDF Page


Link URL




Privacy Policy
ALLDATASHEET.COM
Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Datasheet Upload   |   Contact us   |   Privacy Policy   |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com