M30620FCAFP datasheet(225/274 Pages) MITSUBISHI

225 / 274 page

CPU Rewrite Mode (Flash Memory Version)

Mitsubishi microcomputers

M16C / 62A Group

SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER

225

Precautions on CPU Rewrite Mode

Described below are the precautions to be observed when rewriting the flash memory in CPU rewrite

mode.

(1) Operation speed

During CPU rewrite mode, set the main clock frequency as shown below using the main clock divide

ratio select bit (bit 6 at address 000616 and bits 6 and 7 at address 000716):

6.25 MHz or less when wait bit (bit 7 at address 000516) = 0 (without internal access wait state)

12.5 MHz or less when wait bit (bit 7 at address 000516) = 1 (with internal access wait state)

(2) Instructions inhibited against use

The instructions listed below cannot be used during CPU rewrite mode because they refer to the

internal data of the flash memory:

UND instruction, INTO instruction, JMPS instruction, JSRS instruction, and BRK instruction

(3) Interrupts inhibited against use

The address match interrupt cannot be used during CPU rewrite mode because they refer to the

internal data of the flash memory. If interrupts have their vector in the variable vector table, they can be

_______

used by transferring the vector into the RAM area. The NMI and watchdog timer interrupts each can

be used to change the flash memory’s operation mode forcibly to read array mode upon occurrence of

_______

the interrupt. Since the rewrite operation is halted when the NMI and watchdog timer interrupts occur,

the erase/program operation needs to be performed over again.

Disabling erase or rewrite operations for address FC00016 to address FFFFF16 in the user ROM block

disables these operations for all subsequent blocks as well. Therefore, it is recommended to rewrite

this block in the standard serial I/O mode.

(4) Internal reserved area expansion bit (Bit 3 at address 000516)

The reserved area of the internal memory can be changed by using the internal reserved area expan-

sion bit (bit 3 at address 000516). However, if the CPU rewrite mode select bit (bit 1 at address 03B716)

is set to 1, the internal reserved area expansion bit (bit 3 at address 000516) also is set to 1 automati-

cally. Similarly, if the CPU rewrite mode select bit (bit 1 at address 03B716) is set to 0, the internal

reserved area expansion bit (bit 3 at address 000516) also is set to 0 automatically.

The precautions above apply to the products which RAM size is over 15 Kbytes or flash memory size

is over 192 Kbyte.

(5) Reset

Reset input is always accepted. After a reset, the addresses 0C000016 through 0CFFFF16 are made

a reserved area and cannot be accessed. Therefore, if your product has this area in the user ROM

area, do not write any address of this area to the reset vector. This area is made accessible by

changing the internal reserved area expansion bit (bit 3 at address 000516) in a program.

(6) Access disable

Write CPU rewrite mode select bit, flash memory power supply-OFF bit and user ROM area select bit

in an area other than the internal flash memory.

(7) How to access

For CPU rewrite mode select bit, lock bit disable bit, and flash memory power supply-OFF bit to be set

to “1”, the user needs to write a “0” and then a “1” to it in succession. When it is not this procedure, it

is not enacted in “1”. This is necessary to ensure that no interrupt or DMA transfer will be executed

during the interval.

M30620FCAFP Datasheet(PDF) 225 Page - Mitsubishi Electric Semiconductor

M30620FCAFP Datasheet(HTML) 225 Page - Mitsubishi Electric Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL