Transition TIme=30μS

Transition TIme=30μS

Transition Time=30μS

Transition Time=30μS

No Effect on DC Performance

Input to output or any pin to case @ 500V

BW=10KHz to 2MHz

BW=10KHz to 2MHz

Capacitive Load

Isolation

Short Circuit Current Limit

Switching Frequency

VOUT Adjustment Range

ELECTRICAL SPECIFICATIONS

VDC

VDC

mA

mA

mVrms

mVrms

mArms

mArms

mV

mV

mV

mV

%

%

mV

mV

μS

μS

mV

mV

μS

μS

mV

mV

mS

mS

μS

μS

mS

V

mA

mA

mA

μF

MΩ

A

KHz

%

Min.

15.00

14.80

150

150

-

-

-

-

-

-

-

-

68

58

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

16

-

-

-

-

100

1.5

475

±10

Output Voltage

Output Voltage Ripple

Input Current Ripple

Line Regulation

Load Regulation

Efficiency

Step Load Response

Step Load Recovery

Step Line Response

Step Line Recovery

Start Up Overshoot

Start Up Delay

Shutdown Delay

Parameter

Max.

15.20

15.40

1500

1400

50

60

40

50

±50

±125

±50

±125

-

-

±1200

±1700

200

300

±500

±800

200

300

400

1500

60

100

500

550

60

40

40

50

2.5

300

-

3.0

525

-

BBF2815S

BBF2815S H

Input Voltage Range

Output Current

Units

Typ.

15.10

-

-

-

25

-

20

-

±10

-

±20

-

73

-

±800

-

100

-

±300

-

80

-

0

-

20

-

120

-

20

-

35

-

1.25

-

-

2.4

500

-

Group A

Subgroup

1

2,3

1

2,3

1

2,3

1

2,3

1

2,3

1

2,3

1

2,3

4

5,6

4

5,6

4

5,6

4

5,6

4

5,6

4

5,6

4

5,6

-

1,2,3

1

2,3

1,2,3

1,2,3

1

1

4

1

7

2

Min.

14.95

-

150

-

-

-

-

-

-

-

-

-

68

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

16

-

-

-

-

100

1.5

475

±10

Max.

15.25

-

1500

-

60

-

40

-

±60

-

±60

-

-

-

±1400

-

220

-

±550

-

220

-

500

-

60

-

500

-

60

40

40

-

2.5

300

-

3.0

525

-

Typ.

15.10

-

-

-

25

-

20

-

±10

-

±20

-

73

-

±800

-

40

-

±300

-

80

-

0

-

20

-

120

-

30

-

35

-

1.25

-

-

2.4

500

-

6

Shutdown Recovery

Quiescent Current

2

2

2

2

2

2

BBF2815S

1

2

3

4

5

6

7

Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only.

Industrial grade devices shall be tested to subgroups 1 and 4 unless otherwise specified.

Military grade devices ("H" suffix) shall be 100% tested to subgroups 1, 2, 3 and 4.

Subgroups 5 and 6 testing available upon request.

Device has internal shutdown feature that pulses the output with a low duty cycle during faults.

NOTES:

2

2

2

2

8548-34 Rev. H 4/12