 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
FDC37C78-HT Datasheet(PDF) 53 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
FDC37C78-HT Datasheet(HTML) 53 Page - Microchip Technology |
|
|
53 / 82 page  53 Table 28 - Drive Control Delays (ms) HUT SRT 2M 1M 500K 300K 250K 2M 1M 500K 300K 250K 0 1 .. E F 64 4 .. 56 60 128 8 .. 112 120 256 16 .. 224 240 426 26.7 .. 373 400 512 32 .. 448 480 4 3.75 .. 0.5 0.25 8 7.5 .. 1 0.5 16 15 .. 2 1 26.7 25 .. 3.33 1.67 32 30 .. 4 2 HLT 2M 1M 500K 300K 250K 00 01 02 .. 7F 7F 64 0.5 1 .. 63 63.5 128 1 2 .. 126 127 256 2 4 .. 252 254 426 3.3 6.7 .. 420 423 512 4 8 . 504 508 The choice of DMA or non-DMA operations is made by the ND bit. When this bit is "1", the non- DMA mode is selected, and when ND is "0", the DMA mode is selected. In DMA mode, data transfers are signalled by the FDRQ pin. Non- DMA mode uses the RQM bit and the FINT pin to signal data transfers. Configure The Configure command is issued to select the special features of the FDC. A Configure command need not be issued if the default values of the FDC meet the system requirements. Configure Default Values: EIS - No Implied Seeks EFIFO - FIFO Disabled POLL - Polling Enabled FIFOTHR - FIFO Threshold Set to 1 Byte PRETRK - Pre-Compensation Set to Track 0 EIS - Enable Implied Seek. When set to "1", the FDC will perform a Seek operation before executing a read or write command. Defaults to no implied seek. EFIFO - A "1" disables the FIFO (default). This means data transfers are asked for on a byte-by- byte basis. Defaults to "1", FIFO disabled. The threshold defaults to "1". POLL - Disable polling of the drives. Defaults to "0", polling enabled. When enabled, a single interrupt is generated after a reset. No polling is performed while the drive head is loaded and the head unload delay has not expired. FIFOTHR - The FIFO threshold in the execution phase of read or write commands. This is programmable from 1 to 16 bytes. Defaults to one byte. A "00" selects one byte; "0F" selects 16 bytes. PRETRK - Pre-Compensation Start Track Number. Programmable from track 0 to 255. Defaults to track 0. A "00" selects track 0; "FF" selects track 255. |
Similar Part No. - FDC37C78-HT |
|
Similar Description - FDC37C78-HT |
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.COM |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
