 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
TSW-102-07-L-D Datasheet(PDF) 6 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
TSW-102-07-L-D Datasheet(HTML) 6 Page - Texas Instruments |
|
|
6 / 60 page  www.ti.com 2.3 Analog Signal Connections 2.3.1 Analog Inputs 2.3.2 Analog Output 2.4 Digital Signal Connections 2.4.1 Digital Inputs and Outputs 2.4.2 Digital Controls 2.5 Power Connections EVM Description and Basics Table 2. List of Jumpers (continued) Default Jumper Position Jumper Description JMP14 Installed When installed, shorts across the output capacitor on HPLCOM; remove this jumper if using AC-coupled output drive JMP15 Installed When installed, shorts across the output capacitor on HPROUT; remove this jumper if using AC-coupled output drive JMP16 Installed When installed, shorts HPLCOM and HPRCOM. Use only if these signals are set to constant VCM. JMP17 Installed When installed, shorts across the output capacitor on HPRCOM; remove this jumper if using AC-coupled output drive JMP18 Open Selects onboard EEPROM as Firmware Source. JMP19 Open When installed, allows the USB-MODEVM to hardware reset the device under user control The analog inputs to the EVM can be connected through two different methods. The analog input sources can be applied directly to J13 (top or bottom side) or through the analog headers (J1-3 and J6) around the edge of the board. The connection details of each header/connector can be found in Appendix A. The analog outputs to the EVM can be connected through two different methods. The analog outputs are available from the J13 and J14 (top or bottom) or they may be accessed through J4, J5, J7, J11,and J12 at the edges of the board. The connection details can be found in Appendix A. The digital inputs and outputs of the EVM can be monitored through J16 and J17. If external signals need to be connected to the EVM, digital inputs should be connected via J14 and J15 on the USB-MODEVM and the SW2 switch should be changed accordingly (see Section 2.2.1). The connector details are available in Section A.2. The digital control signals can be applied directly to J16 and J17 (top or bottom side). The modular TLV320AIC3104EVM can also be connected directly to a DSP interface board, such as the 5-6KINTERFACE or HPA-MCUINTERFACE, or to the USB-MODEVM Interface board if purchased as part of the TLV320AIC3104EVM-PDK. See the product folders on the TI Web site for these evaluation modules or the TLV320AIC3104 for a current list of compatible interface and/or accessory boards. The TLV320AIC3104EVM can be powered independently when being used in stand-along operation or by the USB-MODEVM when it is plugged onto the motherboard. 6 TLV320AIC3104EVM and TLV320AIC3104EVM-PDK SLAU218 – August 2007 Submit Documentation Feedback |
Similar Part No. - TSW-102-07-L-D |
|
Similar Description - TSW-102-07-L-D |
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.COM |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
