 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
LIS331DL Datasheet(PDF) 27 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
LIS331DL Datasheet(HTML) 27 Page - STMicroelectronics |
|
|
27 / 42 page  LIS331DL Register description 27/42 Zen bit enables the generation of Data Ready signal for Z-axis measurement channel when set to 1. The default value is 1. Yen bit enables the generation of Data Ready signal for Y-axis measurement channel when set to 1. The default value is 1. Xen bit enables the generation of Data Ready signal for X-axis measurement channel when set to 1. The default value is 1. 7.3 CTRL_REG2 (21h) SIM bit selects the SPI Serial Interface Mode. When SIM is ‘0’ (default value) the 4-wire interface mode is selected. The data coming from the device are sent to SDO pad. In 3-wire interface mode output data are sent to SDA_SDI pad. BOOT bit is used to refresh the content of internal registers stored in the flash memory block. At the device power up the content of the flash memory block is transferred to the internal registers related to trimming functions to permit a good behavior of the device itself. If for any reason the content of trimming registers was changed it is sufficient to use this bit to restore correct values. When BOOT bit is set to ‘1’ the content of internal flash is copied inside corresponding internal registers and it is used to calibrate the device. These values are factory trimmed and they are different for every accelerometer. They permit a good behavior of the device and normally they have not to be changed. At the end of the boot process the BOOT bit is set again to ‘0’. FDS bit enables (FDS=1) or bypass (FDS=0) the high pass filter in the signal chain of the sensor HPcoeff[2:1]. These bits are used to configure high-pass filter cut-off frequency ft. Table 19. CTRL_REG2 register SIM BOOT 0(1) 1. Bit to be kept to “0” for correct device functionality FDS HP FF_WU2 HP FF_WU1 HPcoeff2 HPcoeff1 Table 20. CTRL_REG2 description SIM SPI Serial Interface Mode selection. Default value: 0 (0: 4-wire interface; 1: 3-wire interface) BOOT Reboot memory content. Default value: 0 (0: normal mode; 1: reboot memory content) FDS Filtered Data Selection. Default value: 0 (0: internal filter bypassed; 1: data from internal filter sent to output register) HP FF_WU2 High Pass filter enabled for Free-Fall/WakeUp # 2. Default value: 0 (0: filter bypassed; 1: filter enabled) HP FF_WU1 High Pass filter enabled for Free-Fall/Wake-Up #1. Default value: 0 (0: filter bypassed; 1: filter enabled) HPcoeff2 HPcoeff1 High pass filter cut-off frequency configuration. Default value: 00 (See Table 21) |
Similar Part No. - LIS331DL_08 |
|
Similar Description - LIS331DL_08 |
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.COM |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
