STMPE811_08 datasheet(9/54 Pages) STMICROELECTRONICS

Part #	STMPE811

Description	8-bit port expander with advanced touchscreen controller

Download	54 Pages

Scroll/Zoom	100%

Manufacturer	STMICROELECTRONICS [STMicroelectronics]

Direct Link	http://www.st.com

Logo

9 / 54 page

STMPE811

I2C interface

9/54

4.1

I2C features

The features that are supported by the I2C interface are listed below:

●

I2C slave device

●

Operates at 1.8 V

●

Compliant to Philips I2C specification version 2.1

●

Supports standard (up to 100 Kbps) and fast (up to 400 Kbps) modes

Start condition

A Start condition is identified by a falling edge of SDATA while SCLK is stable at high state.

A Start condition must precede any data/command transfer. The device continuously

monitors for a Start condition and does not respond to any transaction unless one is

encountered.

Stop condition

A Stop condition is identified by a rising edge of SDATA while SCLK is stable at high state. A

Stop condition terminates communication between the slave device and the bus master. A

read command that is followed by NoAck can be followed by a Stop condition to force the

slave device into idle mode. When the slave device is in idle mode, it is ready to receive the

next I2C transaction. A Stop condition at the end of a write command stops the write

operation to registers.

Acknowledge bit

The acknowledge bit is used to indicate a successful byte transfer. The bus transmitter

releases the SDATA after sending eight bits of data. During the ninth bit, the receiver pulls

the SDATA low to acknowledge the receipt of the eight bits of data. The receiver may leave

the SDATA in high state if it does not acknowledge the receipt of the data.

Table 6.

I2C timing

Symbol

Parameter

Min

Typ

Max

Uni

fSCL

SCL clock frequency

0

400

kHz

tLOW

Clock low period

1.3

μ

s

tHIGH

Clock high period

600

ns

tF

SDA and SCL fall time

300

ns

tHD:STA

START condition hold time (after this

period the first clock is generated)

600

ns

tSU:STA

START condition setup time (only relevant

for a repeated start period)

600

ns

tSU:DAT

Data setup time

100

ns

tHD:DAT

Data hold time

0

μ

s

tSU:STO

STOP condition setup time

600

ns

tBUF

Time the bus must be free before a new

transmission can start

1.3

μ

s

Similar Part No. - STMPE811_08

Manufacturer	Part #	Datasheet	Description
STMicroelectronics	STMPE811	651Kb / 64P	Advanced resistive touch screen controller with 8-bit GPIO expander

More results

Similar Description - STMPE811_08

Manufacturer	Part #	Datasheet	Description
STMicroelectronics	STMPE610	752Kb / 56P	S-Touch?? advanced touchscreen controller with 6-bit port expander
	STMPE811	558Kb / 66P	S-Touch® advanced resistive touchscreen controller with 8-bit GPIO expander April 2011
	STMPE811	50Kb / 3P	8-bit port expander with advanced touch screen controller
	STMPE811	651Kb / 64P	Advanced resistive touch screen controller with 8-bit GPIO expander
	STMPE801	393Kb / 26P	8-bit port expander Xpander logic
	STMPE1801BJR	666Kb / 60P	Xpander Logic??18-bit enhanced port expander with keypad controller March 2011 Rev 3
Maxim Integrated Produc...	MAX7310	316Kb / 15P	2-Wire-Interfaced 8-Bit I/O Port Expander with Reset Rev 3; 2/05
STMicroelectronics	STMPE2401	946Kb / 55P	24-bit Enhanced port expander with Keypad and PWM controller Xpander logic
	STMPE2403	890Kb / 63P	24-bit Enhanced port expander with Keypad and PWM controller Xpander logic
	STMPE1601	583Kb / 61P	16-bit enhanced port expander with keypad and PWM controller Xpander Logic

More results

STMPE811 Datasheet(PDF) 9 Page - STMicroelectronics

STMPE811 Datasheet(HTML) 9 Page - STMicroelectronics

Similar Part No. - STMPE811_08

Similar Description - STMPE811_08

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54

Datasheet Download

Link URL