 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
RP144D Datasheet(PDF) 1 Page - Synaptics Incorporated. |
|
||||||||||||||||||||||||||||||
RP144D Datasheet(HTML) 1 Page - Synaptics Incorporated. |
|
|
1 / 18 page  'DWD 6KHHW 2UGHU 1R 0' 5HY 'HFHPEHU 53'53'DQG53' /RZ9ROWDJH9 .IOH[™99ELV 0RGHP'DWD3XPSVIRU'HVNWRS$SSOLFDWLRQV Introduction The CONEXANT ™ RP56D, RP336D, and RP144D Modem Data Pump (MDP) families support data/fax modem, voice coding/decoding, optional full-duplex speakerphone, and optional AudioSpan (Table 1). Low voltage and small size support desktop applications. Downloadable architecture allows upgrading of MDP code from the host/DTE. In V.90/K56flex mode (RP56), the MDP can receive data at speeds up to 56 kbps from a digitally connected V.90- or K56flex-compatible central site modem. These MDPs take advantage of the PSTN which is primarily digital except for the client modem to central office local loop and are ideal for applications such as remote access to an Internet service provider (ISP), on-line service, or corporate site. The MDP can send upstream data at speeds up to V.34 rates. In V.34 data mode (RP56 and RC336), the MDP can connect at the highest data rate the channel can support from 33.6 kbps to 2400 bps with auto-fallback to V.32 bis. In V.32 bis mode, the MDP can connect at the highest data rate the channel can support from 14.4 kbps to 4800 bps with optional auto-fallback to lower rate modulations. Internal HDLC support eliminates the need for an external serial input/output (SIO) device in the DTE for products incorporating error correction and T.30 protocols. Voice mode includes an Adaptive Differential Pulse Code Modulation (ADPCM) voice coder and decoder (codec). The codec compresses and decompresses voice signals for efficient digital storage of voice messages. The codec operates at 28.8k, 21.6k, or 14.4k bps (4-bit, 3-bit, or 2-bit quantization, respectively) with a 7.2 kHz or 8.0 kHz sample rate. A voice pass-through mode allows the host to transmit and receive uncompressed voice samples in 16-bit linear form at 7.2 kHz, 8.0 kHz, or 11.025 kHz sample rate, or in 8-bit A-Law/µ-Law PCM form at 8.0 kHz sample rate. SP models support position-independent full-duplex speakerphone (FDSP) operation using a dual internal integrated analog circuit to interface with the telephone line and the audio input/out (i.e., a headset, handset, or a microphone with external speaker). SP models also support AudioSpan (analog simultaneous audio/voice and data) operation at a data rate of 4.8 kbps. The MDP operates over the public switched telephone network (PSTN) through the appropriate line termination. Features • Downloadable MDP code from the host/DTE • 2-wire full-duplex − V.90 and K56flex (RP56 models) − V.34 (33.6 kbps) (RP56 and RP336 models) − V.32 bis, V.32, V.22 bis, V.22, V.23, and V.21 − Bell 212 and 103 • 2-wire half-duplex − V.34 fax, V.17, V.33, V.29, V.27 ter, and V.21 ch 2 − Bell 208 − Short train option in V.17 and V.27 ter • Serial synchronous and asynchronous data • Parallel synchronous and asynchronous data • Parallel synchronous SDLC/HDLC support • In-band secondary channel (V.34 and V.32 bis) • Automatic mode selection (AMS) • Automatic rate adaption (ARA) • Digital near-end and far-end echo cancellation • Bulk delay for satellite transmission • ADPCM voice mode (7.2 kHz or 8.0 kHz) • Voice pass-through mode (7.2 kHz, 8.0 kHz, or 11.025 kHz) • Full-duplex speakerphone (SP models) − Acoustic and line echo cancellation − Programmable microphone AGC − Microphone volume selection and muting − Speaker volume control and muting; room monitor • AudioSpan (SP models) − ITU-T V.61 modulation (4.8 kbps data plus audio) − Handset, headset, or half-duplex speakerphone • TTL and CMOS compatible DTE interface − ITU-T V.24 (EIA/TIA-232-E) (data/control) − Microprocessor bus (data/configuration/control) • Dynamic range: -9 dBm to -43 dBm • Adjustable speaker output to monitor received signal • DMA support interrupt lines • Transmit and receive (16+128)-byte FIFO data buffers • NRZI encoding/decoding • 511 pattern generation/detection • V.8 and V.8 bis signaling • V.13 signaling • Diagnostic capability − V.54 inter-DCE signaling − V.54 local analog and remote digital loopback • +3.3V operation with +5V tolerant inputs − +5V analog operation • Power consumption: − Normal Mode = 280 mW; Sleep Mode = 53 mW • Low profile, small footprint package − 100-pin PQFP |
Similar Part No. - RP144D |
|
Similar Description - RP144D |
|
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.COM |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
