LIS202DL datasheet(13/36 Pages) STMICROELECTRONICS

Part #	LIS202DL

Description	MEMS motion sensor 2-axis - 짹2g/짹8g smart digital output ?쐏iccolo??accelerometer

Download	36 Pages

Scroll/Zoom	100%

Manufacturer	STMICROELECTRONICS [STMicroelectronics]

Direct Link	http://www.st.com

Logo

13 / 36 page

LIS202DL

Digital interfaces

13/36

5.1.1

I2C operation

The transaction on the bus is started through a START (ST) signal. A START condition is

defined as a HIGH to LOW transition on the data line while the SCL line is held HIGH. After

this has been transmitted by the Master, the bus is considered busy. The next byte of data

transmitted after the start condition contains the address of the slave in the first 7 bits and

the eighth bit tells whether the master is receiving data from the slave or transmitting data to

the slave. When an address is sent, each device in the system compares the first seven bits

after a start condition with its address. If they match, the device considers itself addressed

by the master.

The Slave ADdress (SAD) associated to the LIS202DL is 001110xb. SDO pad can be used

to modify less significant bit of the device address. If SDO pad is connected to voltage

supply LSb is ‘1’ (address 0011101b) else if SDO pad is connected to ground LSb value is

‘0’ (address 0011100b). This solution permits to connect and address two different

accelerometer to the same I2C lines.

Data transfer with acknowledge is mandatory. The transmitter must release the SDA line

during the acknowledge pulse. The receiver must then pull the data line LOW so that it

remains stable low during the HIGH period of the acknowledge clock pulse. A receiver which

has been addressed is obliged to generate an acknowledge after each byte of data has

been received.

The I2C embedded inside the LIS202DL behaves like a slave device and the following

protocol must be adhered to. After the start condition (ST) a salve address is sent, once a

slave acknowledge (SAK) has been returned, a 8-bit sub-address will be transmitted: the 7

LSb represent the actual register address while the MSB enables address auto increment. If

the MSb of the SUB field is 1, the SUB (register address) will be automatically increment to

allow multiple data read/write.

The slave address is completed with a Read/Write bit. If the bit was ‘1’ (Read), a repeated

START (SR) condition will have to be issued after the two sub-address bytes; if the bit is ‘0’

(Write) the Master will transmit to the slave with direction unchanged.

Similar Part No. - LIS202DL

Manufacturer	Part #	Datasheet	Description
Huber+Suhner, Inc.	LIS21_N-50-12-300000	65Kb / 2P	COAXIAL CONNECTOR, N, 50 Ohm, Straight cable jack (female)
	LIS21_N-50-5-300000	133Kb / 2P	COAXIAL CONNECTOR, N, 50 Ohm, Straight cable jack (female)
	LIS21_N-50-7-300000	133Kb / 2P	COAXIAL CONNECTOR, N, 50 Ohm, Straight cable jack (female)
	LIS21_N-50-9-300000	133Kb / 2P	COAXIAL CONNECTOR, N, 50 Ohm, Straight cable jack (female)
STMicroelectronics	LIS244AL	165Kb / 15P	MEMS motion sensor:2-axis - 짹2g ultracompact linear accelerometer

Manufacturer	Part #	Datasheet	Description
STMicroelectronics	LIS35DE	656Kb / 39P	MEMS motion sensor 3-axis - 짹2g/짹8g smart digital output ?쐏iccolo??accelerometer
	LIS302DL	613Kb / 42P	MEMS motion sensor 3-axis - 짹2g/짹8g smart digital output ?쐏iccolo??accelerometer
	LIS302DL	276Kb / 29P	MEMS motion sensor 3-axis - 짹2g/짹8g smart digital output piccolo accelerometer
	LIS33DE	538Kb / 31P	MEMS motion sensor 3-axis - 짹2g/짹8g smart digital output ?쐍ano??accelerometer
	LIS331DL	622Kb / 38P	MEMS motion sensor 3-axis - 짹2g/짹8g smart digital output ?쐍ano??accelerometer
	LIS331DL	647Kb / 42P	MEMS motion sensor 3-axis - 짹2g/짹8g smart digital output -nano-accelerometer
	LIS302DL	608Kb / 42P	MEMS motion sensor 3-axis - 짹 2g/짹 8g smart digital output ?쐏iccolo??accelerometer
	LIS244AL	165Kb / 15P	MEMS motion sensor:2-axis - 짹2g ultracompact linear accelerometer
	LIS302SG	227Kb / 19P	MEMS motion sensor 3-axis - 짹2g analog output -piccolo- accelerometer
	LIS302ALK	160Kb / 14P	MEMS motion sensor 3-axis-짹2g analog output "piccolo" accelerometer