 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
HSDL-3202 Datasheet(PDF) 12 Page - Agilent(Hewlett-Packard) |
|
|
|||||||||||||||||||||||||||||
HSDL-3202 Datasheet(HTML) 12 Page - Agilent(Hewlett-Packard) |
|
|
12 / 16 page  12 The reflow profile is a straight line representation of a nominal temperature profile for a convec- tive reflow solder process. The temperature profile is divided into four process zones, each with different ∆T/∆time tempera- ture change rates. The ∆T/∆time rates are detailed in the above table. The temperatures are measured at the component to printed-circuit board connections. In process zone P1, the PC board and HSDL-3202 castellation I/O pins are heated to a temperature of 125 °C to acti- vate the flux in the solder paste. The temperature ramp-up rate, R1, is limited to 4 °C per second to allow for even heating of both the PC board and HSDL-3202 castellation I/O pins. Process Zone Symbol ∆T Maximum ∆T/∆time Heat Up P1, R1 25 °C to 125°C4°C/s Solder Paste Dry P2, R2 125 °C to 170°C 0.5 °C/s Solder Reflow P3, R3 170 °C to 230°C (245°C max.) 4°C/s P3, R4 230 °C to 170°C–4°C/s Cool Down P4, R5 170 °C to 25°C–3°C/s Reflow Profile 0 t-TIME (SECONDS) 200 170 125 100 50 50 150 100 200 250 300 150 183 230 P1 HEAT UP P2 SOLDER PASTE DRY P3 SOLDER REFLOW P4 COOL DOWN 25 R1 R2 R3 R4 R5 90 sec. MAX. ABOVE 183°C MAX. 245°C Process zone P2 should be of sufficient time duration (> 60 seconds) to dry the solder paste. The temperature is raised to a level just below the liquidus point of the solder, usually 170 °C (338 °F). Process zone P3 is the solder reflow zone. In zone P3, the tem- perature is quickly raised above the liquidus point of solder to 230 °C (446°F) for optimum re- sults. The dwell time above the liquidus point of solder should be between 15 and 90 seconds. It usually takes about 15 seconds to assure proper coalescing of the solder balls into liquid solder and the formation of good solder connections. Beyond a dwell time of 90 seconds, the intermetallic growth within the solder connec- tions becomes excessive, result- ing in the formation of weak and unreliable connections. The tem- perature is then rapidly reduced to a point below the solidus temperature of the solder, usually 170 °C (338°F), to allow the solder within the connections to freeze solid. Process zone P4 is the cool down after solder freeze. The cool down rate, R5, from the liquidus point of the solder to 25 °C (77°F) should not exceed –3 °C per second maximum. This limitation is necessary to allow the PC board and HSDL-3202 castellation I/O pins to change dimensions evenly, putting mini- mal stresses on the HSDL-3202 transceiver. |
Similar Part No. - HSDL-3202 |
|
Similar Description - HSDL-3202 |
|
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.COM |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
