TM124FBK32, TM124FBK32S 1048576 BY 32-BIT

TM248GBK32, TM248GBK32S 2097152 BY 32-BIT

DYNAMIC RAM MODULES

SMMS664A – DECEMBER 1995 – REVISED JUNE 1996

6

POST OFFICE BOX 1443

Voltage range on any pin (see Note 1)

– 1 V to 7 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

– 1 V to 7 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Short circuit output current

50 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Power dissipation: TM124FBK32, TM124FBK32S

8 W

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TM248GBK32, TM248GBK32S

16 W

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

0

°C to 70°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

–55

°C to 125°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only and

functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not

implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

NOTE 1: All voltage values are with respect to VSS.

recommended operating conditions

MIN

NOM

MAX

UNIT

VCC

Supply voltage

4.5

5

5.5

V

VIH

High-level input voltage

2.4

6.5

V

VIL

Low-level input voltage (see Note 2)

– 1

0.8

V

TA

Operating free-air temperature

0

70

°C

NOTE 2: The algebraic convention, where the more negative (less positive) limit is designated as minimum, is used for logic voltage levels only.

electrical characteristics over full ranges of recommended operating conditions (unless otherwise

noted)

PARAMETER

TEST CONDITIONS

’124FBK32-60

’124FBK32-70

’124FBK32-80

UNIT

PARAMETER

TEST CONDITIONS

MIN

MAX

MIN

MAX

MIN

MAX

UNIT

VOH High-level output voltage

IOH = – 5 mA

2.4

2.4

2.4

V

VOL

Low-level output voltage

IOL = 4.2 mA

0.4

0.4

0.4

V

II

Input current (leakage)

VI = 0 to 6.5 V,

VCC = 5 V,

All other pins = 0 to VCC

±10

±10

±10

µA

IO

Output current (leakage)

VO = 0 to VCC,VCC = 5.5 V,

CAS high

±10

±10

±10

µA

ICC1

Read- or write-cycle current

(see Note 3)

Minimum cycle,

VCC = 5.5 V

840

720

640

mA

ICC1 Standby current

After one memory cycle,

RAS and CAS high,

VIH = 2.4 V (TTL)

16

16

16

mA

ICC1 Standby current

After one memory cycle,

RAS and CAS high,

VIH = VCC – 0.2 V (CMOS)

8

8

8

mA

ICC3

Average refresh current

(RAS-only or CBR) (see Note 3)

Minimum cycle,

VCC = 5.5 V,

RAS cycling,

CAS high (RAS-only),

RAS low after CAS low (CBR)

840

720

640

mA

ICC4

Average page current

(see Note 4)

tPC = minimum,

VCC = 5.5 V,

RAS low, CAS cycling

720

640

560

mA

NOTES:

3. Measured with a maximum of one address change while RAS = VIL.

4. Measured with a maximum of one address change while CAS = VIH.