 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
LP3310B6F Datasheet(PDF) 5 Page - Lowpower Semiconductor inc |
|
|
|||||||||||||||||||||||||||||
LP3310B6F Datasheet(HTML) 5 Page - Lowpower Semiconductor inc |
|
|
5 / 9 page  LP3310-00 Jan.-2018 Email: marketing@lowpowersemi.com www.lowpowersemi.com Page 5 of 9 Preliminary Datasheet LP3310 Operation Information LED Current Control The LP3310 regulates the LED current by setting the current sense resistor (R1) connecting to feedback and ground. The internal feedback reference voltage is 200mV. The LED current can be set from following equation easily. ILED = 250mV / R1 In order to have an accurate LED current, precision resistors are preferred (1% is recommended). The table for R1 selection is shown below. Power Sequence In order to assure the normal soft start function for suppressing the inrush current the input voltage should be ready before EN pulls high. Soft-Start The function of soft-start is made for suppressing the inrush current to an acceptable value at the beginning of power-on. The LP3310 provides a built-in soft-start function by clamping the output voltage of error amplifier so that the duty cycle of the PWM will be increased gradually in the soft-start period. Current Limiting The current flow through inductor as charging period is detected by a current sensing circuit. As the value comes across the current limiting threshold, the N-MOSFET will be turned off so that the inductor will be forced to leave charging stage and enter discharging stage. Therefore, the inductor current will not increase over the current limiting threshold. OVP/UVLO/OTP The Over Voltage Protection is detected by a junction breakdown detecting circuit. Once VOUT goes over the detecting voltage, LX pin stops switching and the power N-MOSFET will be turned off. Then the VOUT will be clamped to be near VOVP. As the output voltage is higher than a specified value or input voltage is lower than a specified value, the chip will enter protection mode to prevent abnormal function. As the die temperature is higher than 160℃, the chip also will enter protection mode. The power MOSFET will be turned off during protection mode to prevent abnormal operation. Inductor Selection The recommended value of inductor for 2 to 8 WLEDs applications are 2.2uH to 10µH. Small size and better efficiency are the major concerns for portable device, such as LP3310 used for mobile phone. The inductor should have low core loss at 1.0MHz and low DCR for better efficiency. To avoid inductor saturation current rating should be considered. Capacitor Selection Input ceramic capacitor of 2.2uF and output ceramic capacitor of 1uF are recommended for the LP3310 applications for driving 8 series WLEDs. For better voltage filtering, ceramic capacitors with low ESR are recommended. X5R and X7R types are suitable because of their wider voltage and temperature ranges. |
Similar Part No. - LP3310B6F |
|
Similar Description - LP3310B6F |
|
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.COM |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
