1. Enter binding mode on the Gateway.

•

For housed DX80 Gateways, triple-click button 2 on the Gateway. Both LEDs flash red.

•

For board-level DX80 Gateways, triple-click the binding button on the Gateway. The green and red LED flashes.

2. Assign the Q45VTP a Node address using the Gateway's rotary dials. Use the left rotary dial for the left digit and the right

rotary dial for the right digit. For example, to assign your Q45VTP to Node 10, set the Gateway's left dial to 1 and the right

dial to 0. Valid Node addresses are 01 through 47.

3. Loosen the clamp plate on the top of the Q45VTP and lift the cover.

4. Enter binding mode on the Q45VTP by triple-clicking the Q45VTP's binding button.

The red and green LEDs flash alternately and the sensor searches for a Gateway in binding mode. After the Q45VTP is

bound, the LEDs stay solid momentarily, then they flash together four times. The Q45VTP exits binding mode.

5. Label the sensor with the Q45VTP's Node address number for future reference.

6. Repeat steps 2 through 5 for as many Q45VTP as are needed for your network.

7. After binding all Q45VTP, exit binding mode on the Gateway.

•

For housed DX80 Gateways, double-click button 2 on the Gateway.

•

For board-level DX80 Gateways, double-click the binding button on the Gateway.

For Gateways with single-line LCDs, after binding your Q45VTP to the Gateway, make note of the binding code displayed under

the Gateway's *DVCFG menu, XADR submenu on the LCD. Knowing the binding code prevents having to re-bind all Q45VTPs if

your Gateway is ever replaced.

Bind a Q45 Node to a DXM Gateway and Assign the Node Address

Before beginning the binding procedure, apply power to all the devices. Separate radios by 2 meters when running binding

procedure. Put only one DXM Gateway into binding at a time to prevent binding to the wrong Gateway.

1. On the DXM radio using the arrow keys select the ISM Radio menu on the LCD and click ENTER.

2. Highlight the Binding menu and click ENTER.

3. Use the arrow keys to select the Node address to bind the Q45VTP to.

4. Loosen the clamp plate on the top of the Q45VTP and lift the cover.

5. Enter binding mode on the Q45VTP by triple-clicking the power/binding button.

The red and green LEDs flash alternately and the sensor searches for a Gateway in binding mode. After the Q45VTP binds,

the LEDs stay solid momentarily, then they flash together four times. The Q45 exits binding mode.

6. Label the sensor with the Q45VTP's Node address number for future reference.

7. Click BACK on DXM to exit binding for that specific Node address.

8. Repeat steps 3 through 7 changing the Node address for as many Q45VTPs as are needed for your network.

9. Click BACK on DXM until back to the main menu when finished binding.

DIP Switches

After making any changes to any DIP switch position, reboot the Q45VTP by triple-clicking the button, waiting a second, then

double-clicking the button.

The DIP switches are in the OFF position. To turn a DIP switch on, push the switch toward the battery pack. DIP switches one

through four are numbered from left to right.

Description

DIP Switches

1

2

3

4

5

6

7

8

Transmit power: 1 Watt

OFF*

Transmitt power: 250 mW (compatible with 150 mW radios)

ON

Default I/O configuration1

OFF*

OFF*

OFF*

I/O configuration 1

OFF

OFF

ON

I/O configuration 2

OFF

ON

OFF

I/O configuration 3

OFF

ON

ON

I/O configuration 4

ON

OFF

OFF

I/O configuration 5

ON

OFF

ON

1 User configurable if switch 7 is OFF; for input serial addresses, see Modbus Registers and I/O Serial Addresses on page 5

P/N 208637 Rev. A

www.bannerengineering.com - Tel: +1-763-544-3164

3