General Description Introduction The MC68HC908GZ16 is a member of the low-cost, high-performance M68HC08 Family of 8-bit microcontroller units (MCUs). All MCUs in the family use the enhanced M68HC08 central processor unit (CPU08) and are available with a variety of modules, memory sizes and types, and package types. Features For convenience, features have been organized to reflect: • Standard features • Features of the CPU08 Standard Features Features include: • High-performance M68HC08 architecture optimized for C-compilers • Fully upward-compatible object code with M6805, M146805, and M68HC05 Families • 8-MHz internal bus frequency • Clock generation module supporting 1-MHz to 8-MHz crystals • MSCAN08 (implementing 2.0b protocol as defined in BOSCH specification dated September 1991) • FLASH program memory security(1) • On-chip programming firmware for use with host personal computer which does not require high voltage for entry • In-system programming (ISP) • System protection features: – Optional computer operating properly (COP) reset – Low-voltage detection with optional reset and selectable trip points for 3.3-V and 5.0-V operation – Illegal opcode detection with reset – Illegal address detection with reset • Low-power design; fully static with stop and wait modes • Standard low-power modes of operation: – Wait mode – Stop mode • Master reset pin and power-on reset (POR) • On-chip FLASH memory: – MC68HC908GZ16 — 16 Kbytes – MC68HC908GZ8 — 8 Kbytes • 1 Kbyte of on-chip random-access memory (RAM) • 406 bytes of FLASH programming routines read-only memory (ROM) • Serial peripheral interface (SPI) module • Enhanced serial communications interface (ESCI) module • Fine adjust baud rate prescalers for precise control of baud rate • Arbiter module: – Measurement of received bit timings for baud rate recovery without use of external timer – Bitwise arbitration for arbitrated UART communications • LIN specific enhanced features: – Generation of LIN 1.2 break symbols without extra software steps on each message – Break detection filtering to prevent false interrupts • Two 16-bit, 2-channel timer interface modules (TIM1 and TIM2) with selectable input capture, output compare, and pulse-width modulation (PWM) capability on each channel. One 2-channel timer and one 1-channel timer on the 32-pin package. • Up to 8-channel, 10-bit successive approximation analog-to-digital converter (ADC) depending on package choice • BREAK (BRK) module to allow single breakpoint setting during in-circuit debugging • Internal pullups on IRQ and RST to reduce customer system cost • Up to 37 general-purpose input/output (I/O) pins, including: – 28 shared-function I/O pins – Up to nine dedicated I/O pins, depending on package choice • Selectable pullups on inputs only on ports A, C, and D. Selection is on an individual port bit basis. During output mode, pullups are disengaged. • High current 10-mA sink/source capability on all port pins • Higher current 20-mA sink/source capability on PTC0–PTC4 • Timebase module (TBM) with clock prescaler circuitry for eight user selectable periodic real-time interrupts with optional active clock source during stop mode for periodic wakeup from stop using an external crystal • User selection of having the oscillator enabled or disabled during stop mode • Up to 8-bit keyboard wakeup port depending on package choice • 2 mA maximum current injection on all port pins to maintain input protection • Available packages: – 32-pin quad flat pack (LQFP) – 48-pin quad flat pack (LQFP) • Specific features of the MC68HC908GZ16 in 32-pin LQFP are: – Port A is only 4 bits: PTA0–PTA3; 4-pin keyboard interrupt (KBI) module – Port B is only 6 bits: PTB0–PTB5; 6-channel ADC module – Port C is only 2 bits: PTC0–PTC1; shared with MSCAN08 module – Port D is only 7 bits: PTD0–PTD6; shared with SPI, TIM1, and TIM2 modules – Port E is only 2 bits: PTE0–PTE1; shared with ESCI module • Specific features of the MC68HC908GZ16 in 48-pin LQFP are: – Port A is 8 bits: PTA0–PTA7; 8-pin KBI module – Port B is 8 bits: PTB0–PTB7; 8-channel ADC module – Port C is only 7 bits: PTC0–PTC6; shared with MSCAN08 module – Port D is 8 bits: PTD0–PTD7; shared with SPI, TIM1, and TIM2 modules – Port E is only 6 bits: PTE0–PTE5; shared with ESCI module
|